Ultra Start 32 SERIES Скачать руководство пользователя

Страница: 9 / 24

Auxiliary Connectors

continued from previous page

11-Black

Ground

System Chassis Ground Input.

12-Blue

Glow Plug -

Diesel Glow plug input, detects both 12volt and negative glow

plug signals. Programmable input. See Menu 3.

13-Blue/White

Tach

A/C Tach Signal Input. Used to detect when the vehicle has

started. This wire is connected to the vehicles coil, fuel injector or crank
sensor wire.

14-Pink

Brake input -

Positive Brake Input. Used to detect the brake switch being

Applied. Found at the brake switch connector.

15-Wht/Violet

GWR -

(-) Output while remote starter is activated. Used to activate

Anti-theft bypass modules, adding 3rd ign etc.

3 Pin Connector Red

1-Green

Door Lock -

Door Lock Output - Programmable Menu 1 Setting 3.

2-Red

12volt Output - *

Output For Door Lock Module Only!

3-Blue

Door Unlock -

Door Unlock Output - Programmable Menu 1 Setting 3.

* The centre pin of the keyless entry harness is not to be used for anything besides

plug-in devices such as the VP-1, DL-3, DL-7 and Data Bus Modules.

Overloading this output will damage the remote starter.

4 Pin Connector Blue

RF Antenna/ Program Button Connector.
Remove the plastic from the adhesive tape and place the antenna in the center of the
windshield, behind the rear view mirror. Run the cable behind the head liner and

A-pillar panels to the module under the dash.

***The Antenna Must Be Connected Before the System will Operate.***

2 Pin Connector White

Connector for Instant Start Input or Temperature Sensor on LT models.

Note

: This Input is not available on the 3250 Series.

3 Pin Connector White

1- White/Violet GWR -

round output while running. This output can be used for bypass

module activation or adding additional relays.

2- Black Ground -

Low current constant ground output

3- Red- 12volts -

Low current constant 12volt output.

Page 9

2WAY REMOTE VEHICLE STARTER

INSTALLATION MANUAL

Содержание 32 SERIES

























Результаты поиска

Содержание 32 SERIES

Отзывы:

Похожие инструкции для 32 SERIES

Бренды по названию

Популярные бренды

Ultra Start 32 SERIES, Инструкция по установке

Результаты поиска

Содержание 32 SERIES

Отзывы:

Похожие инструкции для 32 SERIES

Бренды по названию

Популярные бренды