Ultra Start 32 SERIES Скачать руководство пользователя

Страница: 17 / 24

Menu 2- Additional

Settings

Ignition

ON-OFF-ON-OFF-ON

Press & Release

Program Button

Press Button #2

Setting 1 Secure Valet Mode - Length of time required to set the system into Service Mode

1) Secure Valet

1 Flash/Honk

Hold the Program Button for 15 seconds

*2) Normal Valet

2 Flashes/Honks

Hold the Program Button for 5 seconds

Press & Release the Program Button 1 Time

(Setting 1) confirmed 1 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/horn (optional)honks, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 2 Parking Light/Trunk Output (14 pin auxiliary connector pins 2&8)

1) 30 sec. Output

1 Flash/Honk

Park Lights on for 30 seconds when Unlock is pressed

2) Negative Park Lights

2 Flashes/Honks

Switches the Park Lights/Trunk Outputs

*3) Park Lights

3 Flashes/Honks

Park light flash as confirmation of feature activation.

Press & Release the Program Button 2 Times

(Setting 2) confirmed 2 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/horn (optional)honks, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 3 Horn Honk Timing (14 pin auxiliary connector pin 5)

1) 5 ms Pulse Output

1 Flash/Honk

Short(Quiet) Horn Output Pulses

2) 15 ms Pulse Output

2 Flashes/Honks

Long(Loud) Horn Output Pulses

*3) 10 ms Pulse Output 3 Flashes/Honks

Normal(Medium) Horn Output Pulses

Press & Release the Program Button 3 Times

(Setting 3) confirmed 3 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/horn (optional)honks, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 4 Button #4 Programmable

1) Trunk Release

1 Flash/Honk

Holding button #4 will activate Trunk Release

2) Garage Door

2 Flashes/Honks

Activates optional Garage Door Interface

3) Car Finder

3 Flashes/Honks

Holding Button #4 activates Car Finder

Press & Release the Program Button 4 Times

(Setting 4) confirmed 4 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/horn (optional)honks, then release.

Press & Release the Program Button

to proceed to the next step

Setting 5 Reservation Mode (”M” units only)

1) Manual Reservation

1 Flash/Honk

Activate Reservation Mode by pressing Button #4

*2) Auto Reservation

2 Flashes/Honks

Activate Reservation Mode by pressing brake

Press & Release the Program Button 5 Times

(Setting 5) confirmed 5 LED flashes.

Press & Hold the Program Button

until the appropriate # of park light/horn (optional)honks, then release.

Press & Release the Program Button

to proceed to the next step.

2WAY

REMOTE VEHICLE STARTER

INSTALLATION MANUAL

Ignition 3x
On/Off
On/Off On

Press and
Release the
Program
Button

Press and
Release the
Program Switch
1x =Setting 1
2x =Setting 2
3x =Setting 3....

Press and
Hold the
Program Switch
1x = Option 1
2x = Option 2
3x = Option 3....

Press button
2 to enter
Program
Menu 2

1 2 3

Содержание 32 SERIES

























Результаты поиска

Содержание 32 SERIES

Отзывы:

Похожие инструкции для 32 SERIES

Бренды по названию

Популярные бренды

Ultra Start 32 SERIES, Инструкция по установке

Результаты поиска

Содержание 32 SERIES

Отзывы:

Похожие инструкции для 32 SERIES

Бренды по названию

Популярные бренды