![background image](http://html2.mh-extra.com/html/ufesa/as3010/as3010_instruction-manual_3312926010.webp)
attached to it get choked or “CYCLONE” dust
container is overfull. Once the valve opens, you
will hear a distinctive “whirring” sound coming
out of the machine.
1
Switch the vacuum off by pressing ON/OFF
button
(7)
.
2
Remove the plug from the power outlet.
3
Press the two side buttons located on the hose end
and remove the ending of the hose from the inlet opening.
4
Raise the front cover interlock
(8)
and open the lid
(6)
.
5
Remove “CYCLONE” dust container
(15)
from the
vacuum.
6
Move “CYCLONE” dust container over the dust bin.
Release the interlock on the “CYCLONE” container and
open the lid. Empty the container.
7
After emptying the container, close the cover.
Container’s lid must be tightly closed.
Otherwise the dust will penetrate into
your vacuum’s compartment and the
suction power will be decreased.
8
Insert the emptied “CYCLONE” container into the
vacuum cleaner.
It is necessary to empty “CYCLONE” dust container when
you notice that:
a) your vacuum cleaner is vacuuming less effectively,
b) “CYCLONE” dust container is full.
Do not vacuum if “CYCLONE” dust
container is not attached.
End of operation, cleaning and
maintenance
1
Switch the vacuum off by pressing ON/OFF
button
(7)
.
2
Remove the plug from the power outlet.
3
Wind the cord by pressing cord rewind button
(4)
.
While doing it, remember to hold the cord to make sure
it does not get tangled and the plug does not hit the
vacuum’s hosing.
4
Disconnect the telescopic tube and the nozzle or
the brush.
5
Disconnect the telescoping suction tube from the
hose. In order to remove the telescopic handle from
F
the hose handle, press latch
“A”
and pull the tube
towards the arrow.
6
Press the two side buttons located on the hose end
and remove the ending of the hose from the inlet opening.
7
Your vacuum cleaner may be stored in horizontal
and vertical position. The hose may stay fastened to
the vacuum cleaner, but make sure that it is not bent
too hard when stored.
Horizontal storing:
–
insert the fastening hook of the suction brush into
the clip fastening the suction brush which is located
on the back side of the vacuum.
Vertical storing:
–
insert the suction brush fastening hook into the clip
fastening the suction brush which is located at the
bottom of the vacuum right next to to the back wheel.
8
If necessary, the vacuum’s housing and compartment
may be wiped with a wet cloth (it may be moistened with
a detergent), dried or wiped until dry.
Do not use scouring agents or solvents.
Problems that may occur when
operating the vacuum
PROBLEM
WHAT TO DO
You can hear the
“whirring” sound.
●
Check “CYCLONE” dust
container and the fittings,
remove the clog or empty and
clean the “CYCLONE” dust
container.
●
Replace or clean the filters.
Your vacuum
cleaner is not
working efficiently
enough.
Empty and clean “CYCLONE”
dust container, replace the
filters, check the suction tube,
hose and nozzle - remove
the clog.
Power installation
fuse went on.
Check whether there are other
electric appliances plugged
into the same electric circuit,
if the fuse turns on repeatedly,
take the vacuum cleaner to
the service.
Содержание AS3010
Страница 22: ...CYCLONE ON OFF 1 7 2 4 3 4 5 A 6 7 8 F CYCLONE CYCLONE CYCLONE...
Страница 25: ...UFESA 8 16 240 220 AR...
Страница 26: ...Notes...