background image

Electronic  Service

Manuals

This electronic document is provided as a service to our customers.
We do not create the contents of the information contained in this docu-
ment.  Should you have detailed questions pertaining to the information
contained in this document, you may contact Michco, or the manufac-
turer which provided the original information in this electronic deliver-
able.  Michco’s only part in this electronic deliverable was the electronic
assembly process.  By providing this manual on line we are not guaran-
teeing parts availability.

You may contact Michco through the following methods:

Phone (517) 484-9312 or (800) 331-3339

2011 N. High St.  -- Lansing, Michigan -- 48906

Fax: (517) 484-9836

Email: [email protected]

Web site: www.Michco.Com

Parts Web site:  www.FloorMachineParts.Com

Order Parts on Line at:

www.FloorMachineParts.Com

Directly to Parts & Service:

By Email: 

[email protected]

By Fax: (517) 702-2041

By Voice: Use numbers above.

Serving the Cleaning Industry Since 1922

Notice: All copyrighted material remains property of original owners, all trademarks are property of respective owners.
Manuals are subject to Manufacturer’s reproduction limitations.  Originals or reproductions were provided by manufacturers
through a request.  We make no warranty as to the correctness of information provided in this document and you assume
all risk.  By placing these manuals on line we are not declaring our corporation to be an manufacturer authorized dealer or
provider, please check our web site for authorized manufacturers we represent.

Summary of Contents for PB-12


























Reviews: