background image

5

© 2021 Ubicquia Inc.  |  All rights reserved. Patent pending. Public use approved.  |  2058 v2 October 2021

5. Mounting the Unit

5.2

  

Only for APAI units:

 Place the 

attached camera assembly on top 

of the UbiHub unit in the box and 

then gently remove the unit from 

the box.

NOTE:

 The camera is shipped  

wrapped in protective 

packaging and connected to 

the unit. Do not remove the 

protective packaging until 

instructed to.

CAUTION:

 Be careful not to 

swing, slam, or knock the 

camera during installation. The 

camera should be placed atop 

the unit during install, whenever 

possible. 

5.1

  Remove the UbiHub from the 

shipping box by first gently lifting 

the unit with the attached camera 

placed on top. The camera is 

shipped pre-installed and connected 

to the unit by a cable. Caution: Take 

care not to swing, slam, or knock 

the camera during installation. The 

camera should be placed atop 

the unit during install, whenever 

possible. 
Make sure clamp is open with the 

swivel locking nut up out of the way 

before installing on the luminaire.

5.3 

 Attach a safety tether to both 

UbiHub and the lift using the tether 

ring on the UbiHub

If your luminaire has a photocell 

installed, remove it and set it aside 

for later.

6. Prep for Installation

6.1

  Verify the NEMA socket on 

the luminaire is oriented in the 

correct direction. The North 

indication on the NEMA (N >) 

should face away from the pole 

of the luminaire.
If your NEMA socket orientation 

does not match the image 

above, then you will need to 

adjust the NEMA to match.

6.2

   Follow the instructions below 

that match the type of NEMA 

socket on the luminaire to adjust 

the orientation:

NOTE:

 The UbiHub works with 

3, 5, and 7 pin NEMA options.

Содержание UBH-H-AI











Отзывы: