uAvionix tailBeaconX TSO Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 46

background image

UAV-1004270-001

28

Rev A

2. Connect the tailBeaconX red wire to the switched position light power

wire using environmental splices or equivalent.

3. Connect the tailBeaconX black wire to the battery or airframe ground.
4. Connect the tailBeaconX orange and grey wires to the 2 twisted pair

conductors connected to the control head or equivalent equipment.

The exposed (non-shielded) portions of the interface conductors AND
ground drains are to remain less than 2.5 inches.

2.5 Inches Maximum

Non Shielded

Shielded

5. Where required, connect the tailBeaconX white wire to the twisted

pair conductor connected to the aircraft suppression bus. tailBeaconX
implements suppression input only.

If not used, connect the white

wire to aircraft ground.

6. Connect the twisted pair shield to the local airframe ground.
7. Ensure the twisted pair conductors are terminated to the interfaced

control head or equivalent equipment in the panel.

«
...
26
27
28
29
30
...
»

Содержание tailBeaconX TSO















































Отзывы:

Нет отзывов

Похожие инструкции для tailBeaconX TSO

Бренд: Radwin Страницы: 252

Бренд: Radwin Страницы: 6

Бренд: Teac Страницы: 28

Бренд: VDO Страницы: 20

Бренд: Salora Страницы: 35

Бренд: Scott Страницы: 4

Бренд: Majestic Страницы: 22

Бренд: Raymarine Страницы: 47

NAVILED PRO 2NM

Бренд: Hella marine Страницы: 4

Бренд: Uniden Страницы: 23

Бренд: Hama Страницы: 70

Бренд: Cobra Страницы: 21

MC522BC LCD Microphone

Бренд: GME Страницы: 24

Бренд: Cobra Страницы: 19

Бренд: AWA Страницы: 9

Бренд: Samsung Страницы: 2

Smart MBS RRH-C2

Бренд: Samsung Страницы: 31

Бренд: Samsung Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды