uAvionix tailBeaconX TSO Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 46

background image

UAV-1004270-001

24

Rev A

7.5.1.1 Direct Mounting Dimensions

Direct mounting plate UAV-1003125-001 shown.

7.5.1.2 Mounting Plate Installation

The mounting plate utilizes either the included #4-40 or #6-32 mounting
hardware. The mounting plate can be installed with the screw pattern
oriented either vertically or horizontally as shown above. Determine the
orientation of the existing aft position light mounting hardware, and install
the mounting plate accordingly.

1.  Remove the existing aft position light.
2.  Detach the power wire(s) and protect them from damage
3.  Ensure the thru-hole in the tail cone or rudder is at least 36.5mm in

diameter and allows straight passage of the tailBeaconX main body.

4. Peel the backing from the Mounting Gasket and affix to the Mounting

Plate.

«
...
22
23
24
25
26
...
»

Содержание tailBeaconX TSO















































Отзывы:

Нет отзывов

Похожие инструкции для tailBeaconX TSO

Бренд: Radwin Страницы: 252

Бренд: Radwin Страницы: 6

Бренд: NEC Страницы: 98

Бренд: Facnor Страницы: 33

Бренд: JBL Страницы: 9

Бренд: Yaesu Страницы: 13

Xpress XMCK-20KC

Бренд: Audiovox Страницы: 2

Бренд: perfect pro Страницы: 177

Бренд: Sonoro Страницы: 136

Бренд: C. Crane Страницы: 26

Бренд: Revo Страницы: 13

FR-7041R-MARK-2

Бренд: Furuno Страницы: 66

Бренд: Renkforce Страницы: 8

Бренд: Benthos Страницы: 68

Бренд: Daewoo electricals Страницы: 9

Бренд: Rockford Fosgate Страницы: 8

Бренд: Harris Страницы: 264

Бренд: Kenwood Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды