U-Line U-3018CLRINT-00C Скачать руководство пользователя

Страница: 47 / 50

R-600A Specifications

USER GUIDE

R-600A Specifications 4

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE •

SERVICE

The low side of the refrigeration system (evaporator,
compressor and suction line) must be leak tested with the
compressor off (equalized pressure).

RECHARGING

No air is ever to be allowed inside the refrigeration system
(R-600a refrigerant or dry nitrogen only).

Never use a torch on a fully charged refrigeration system.

Install a Schrader Type access port on the compressor
process stub.

Evacuate the system to 100 microns prior to charging.

Weigh in the R-600a charge using a refrigerant scale. (run
compressor an extra two minutes to clear the charging
hoses).

Seal the Schrader Type access port, a proper cap and seal
must be used to close the system.

SUMMARY

Safely handling R-600a requires proper procedures and
training.

R-600a approved service tools must be used.

R-600a labeling must not be removed or altered.

Proper ventilation during service is required.

Never apply a torch to a charged R-600a refrigeration
system.

Use OEM replacement service parts and do not alter the
construction of the unit.

Содержание U-3018CLRINT-00C



















































Результаты поиска

Содержание U-3018CLRINT-00C

Отзывы:

Похожие инструкции для U-3018CLRINT-00C

Бренды по названию

Популярные бренды

U-Line U-3018CLRINT-00C, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U-3018CLRINT-00C

Отзывы:

Похожие инструкции для U-3018CLRINT-00C

Бренды по названию

Популярные бренды