background image

0513 IH-3778

PAGE 8 OF 10

OPERATING INSTRUCTIONS CONTINUED

SWING OPERATION:

When you turn on the unit, the louver will swing and stop 

at a certain angle. You can press the SWING button 

to let the louver swing automatically. Press the SWING 

button again when you want the louver stop at desired 

angle.

CHECK FILTER FEATURE:

This feature is a reminder to clean the Air Filter (See 

Care and Cleaning) for more efficient operation. The 

LED (light) above the "Filter" button will illuminate after 

250 hours of operation. To reset after cleaning the filter, 

press the "Filter" button and the light will go off.

FAULT CODE:

If the display reads "EA", the room 

temperature sensor has failed. Contact 

Uline Customer Service.

If the display reads "ES", the evaporator 

temperature sensor has failed. Contact 

Uline Customer Service.

If the display reads "E4", the display 

panel communication has failed. 

Contact your Uline Customer Service.

If the display reads "P1", bottom tray is 

full. Carefully move the unit to a drain 

location, remove the bottom drain plug 

and let the water drain away. Restart 

the machine until the "P1" symbol  

disappears. If error repeats, call for 

service.

DRAINAGE:

During the dehumidifying mode, you will need a 

garden hose (sold separately) to drain the condensate 

from the unit. Remove the rubber stopper from the hose 

connector. (See Figure 22) 

 

The hose may then: 

A. Discharge into a drain that is lower than the unit.

B. Be connected to a condensate pump (sold 

separately).

REMOTE CONTROL STORAGE:

Door on the side of 

the unit is for storing 

the remote. To open, 

press it (See Figure 23), 

to close, simply push it 

back into position.

Remove the 

supplied rubber 

stopper  

Garden hose

Press here

Figure 22

Figure 23

Содержание H-3778











Отзывы: