manualshive.com logo in svg

U-Line H-1030, Руководство по эксплуатации

Поделиться
Скачать
U-Line H-1030 Скачать руководство пользователя страница 2

PAGE 2 OF 24 

0323 IH-1030

SETUP

LUBRICATION & MAINTENANCE

1.  Lubricate stapler prior to initial operation.

2.  Disconnect the stapler from the air supply prior to 

servicing.

3.  Turn the stapler so that the inlet is facing up and put 

one drop of high-speed spindle oil, UNOCOL RX22, 

or 3-in-1 oil into air inlet. Never use detergent oil or 

additives.

4.  Operate the tool briefly after adding oil.

5.  Wipe off excessive oil at the exhaust. Excessive 

oil will damage the O-rings. If inline oiler is used, 

manual lubrication through the air inlet is not 

required on a daily basis.

AIR SUPPLY AND CONNECTIONS

Ensure air supply system is setup correctly for increased 

the efficiency and life of the stapler. (See Figure 1)

Many air tool users find it convenient to use an inline 

oiler to provide oil circulation through their tool. Check 

oil level in the oiler daily.

NOTE: A filter is recommended on your air 
compressor. Check the filter and drain on  
a daily basis.

OPERATION

LOADING THE STAPLER

1.  Disconnect the air supply.

2.  Slightly squeeze the cover back, then pull top cover 

open. (See Figure 2)

3.  Place coil staples in magazine. Feed front end of coil 

staples into right coil guide, left coil guide and top 

guide. Push forward until stopping in driver guide unit. 

(See Figure 3)

4.  Swing cover closed and squeeze to snap closed. 

Check position engagement. (See Figure 3)

Figure 2

Figure 3

Figure 1

Compressor

Filter

Regulator

Oiler

Quick  

Coupler

Quick  

Connector

Air Hose

Quick  

Coupler

Quick  

Connector

Содержание H-1030

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды