manualshive.com logo in svg
background image

PAGE 12 OF 13 

0922 IH-10066

TROUBLESHOOTING

OPERATING ISSUE

CAUSES

RECOMMENDATIONS

Battery display remains 

dark.

Battery faulty/fully discharged.

Inserted battery not permitted 

(wrong battery).

Battery not properly inserted.

Charge/replace battery.

Insert correct battery.

Check whether battery is completely 

inserted and unlocking device engaged.

User interface and tool 

status indicator do  

not react.

Sleep mode is activated.

Actuate trigger.

Tool status indicator  

red and pulsating 

(stapler blocked).

Process sequence warning.

Actuate trigger. 

Remove jammed staples; see page 10.

Tool status indicator 

pulsating quickly.

Staple encounters obstacle.

Clamp does not go through carton 

(too hard).

Ensure that there are no obstacles.

Only staple common corrugated material.

No stapling performed 

when actuating trigger.

Box detection not activated (tool 

not on carton).

Place tool on carton.

Skipping staples or 

intermittent feed.

Magazine not mounted correctly.

Staples out of specification.

Magazine quick release buttons 

not locked.

Magazine dirty/debris inside.

Driver blade/clinchers dirty/debris 

inside.

Install magazine; see page 10.

Replace with recommended staples.

Lock magazine quick release buttons.

Clean magazine.

Clean/replace driver blade and/or clinchers;  

see page 11.

Staple jammed in tool.

Wrong staple size.

Bent staples.

Staples out of specification.

Defective/dirty driver blade.

Replace with recommended staples.

Clean/replace driver blade and/or  

clinchers; see page 11.

Slow stapling speed or 

blocked.

Battery fully discharged.

Carton too thick.

Charge/replace battery.

Use other carton thickness.

Poor staple clinch.

Wrong leg length setting.

Wrong penetration setting.

Wrong clinch setting.

Driver blade/clinchers dirty/ 

debris inside.

Adjust staple length; see page 9.

Adjust penetration depth; see page 9.

Adjust staple clinch; see page 9.

Clean/replace driver blade and/or clinchers;  

see page 11.

Содержание H-10066














Отзывы: