background image

02/2005

9

www.U-LineService.com

WH95TP, BI95BTP and BCM95 Ice Makers

2. Locate the compression fitting and ferrule packed with 

the unit. Slide the compression fitting and ferrule over 
the 1/4-inch OD water supply line. Do not use thread 
sealing compound or tape. Using two wrenches, 
tighten the compression fitting on the supply line (see 

Figure 18

).

3. Carefully bend the water supply line into position and 

connect the line to the solenoid valve (see 

Figure 19

). 

Avoid kinking the water supply line.

IMPORTANT

Route the water supply line through the unit so it does not 
come into contact with any internal components other 
than the solenoid valve. See 

Figure 20

. Normal operation 

creates some vibration. A water supply line contacting an 
internal component or cabinet wall can cause excessive 
noise during operation or damage to the line.

4. For recessed installations, allow extra water supply line 

length to provide slack for easy removal from the 
recessed area (see 

Figure 20

). This will also safeguard 

against kinking the line. 

5. Go on to 

7 Prepare Power Supply

.

Electrical Specifications

CAUTION

Electrical installation must observe all state and local 
codes. This unit requires connection to a grounded (three-
prong), polarized receptacle that has been placed by a 
qualified electrician.

The unit requires a grounded and polarized 115 VAC, 
60 Hz, 15A power supply (normal household current) 
or a 220 VAC, 50/60 Hz power supply. An individual, 
properly grounded branch circuit or circuit breaker is 
recommended. GFCI (ground fault circuit interrupter) is 
usually not required for fixed location appliances and is 
not recommended for your unit because a GFCI could be 
prone to nuisance tripping. However, be sure to consult 
your local codes.

See 

Figure 21

 for recommended receptacle location. 

WARNING

SHOCK HAZARD — Electrical Grounding Required. 

• Never remove the round grounding prong from 

the plug and never use a two-prong grounding 
adapter.

• Never use an extension cord to connect power to 

the unit.

Go on to 

8 Level the Unit

.

Water Line

Figure 19

Figure 18

Figure 20

7 Prepare Power Supply

1-1/2"

7"

18-1/2" Minimum

Figure 21

Содержание BCM-95













Отзывы: