background image

02/2005

7

www.U-LineService.com

WH95TP, BI95BTP and BCM95 Ice Makers

(BI95BTP units only)

Units will accept a Custom 1/4" Thick Insert to harmonize 
with or accent the surrounding decor. 

If this treatment is not included in this installation, go on 
to 

5 Adjust Door

.

Custom 1/4" Thick Door Panel Insert

Door Panel Preparation

A custom door panel can be inserted into the doorframe. 
Custom door panels can be flat or raised, as long as the 
maximum panel thickness where inserted into the door 
reveal (channel) is 1/4"-thick. For raised panels, the depth 
of the reveal is 1/4" on all four sides.

IMPORTANT

Raised panels will reduce the door’s 90° swing/zero 
clearance if the unit is installed next to a wall or similar 
type of structure (see 

Page 4

).

Cut the panel insert to the following dimensions.

Custom 1/4" Dimensions:

Width:

12-15/16"

Height:

13-15/32"

The door panel must not weigh more than 20 lbs.

Door Panel Installation

Install the insert as follows:

CAUTION

Use care when handling the insert. Insert edges may be 
sharp.

1. Remove top hinge screw pin with a Phillips head 

screwdriver (see 

Figure 14

). Remove door by tilting 

forward and lifting off bottom hinge pin.

2. Pull door gasket out of 

groove (top edge of door 
only). Start in the middle 
and pull outward, moving 
toward the edge (see 

Figure 15

). This may take 

some force.

3. Remove two outside 

screws holding door 
handle. Slightly separate 
door handle from door 
(see 

Figure 16

).

4. Pull handle up and off.

5. Slide custom door panel insert into 1/4-inch channel in 

door front.

6. Holding door gasket out of the way, replace handle on 

door, making sure it is seated properly on insert and 
that screw holes line up.

7. Install two small screws removed in

 

Step 3.

8. Starting at the corners and working inward, push door 

gasket into place on door.

9. Place door on bottom hinge pin and install upper hinge 

screw.

10. Go on to 

5 Adjust Door

.

4 Prepare and Install Door Panel

Figure 14

Figure 15

Figure 16

Содержание BCM-95













Отзывы: