TYROLIT Hydrostress SK-SD Скачать руководство пользователя страница 43

Страница: 43 / 66

Operating Instructions

Assembly / disassembly

SK-SD / 007

4-9

4.3.7

Wire saw SK-SD Connect to the drive unit

4.3.7.1

Fundamentals

• Clean the couplings regularly

• Connect together both ends of any hoses, which are not used, so that

the couplings are protected

• Always switch off the drive unit and relieve the pressure in the hoses

before handling the wire saw SK-SD

4.3.7.2

Releasing pressure in the hose

1. Hoses that are coupled to the drive unit:

(see drive unit Operating Instructions)

2. Hoses that are not coupled:

Position pressure relief device on hose on the coupling and screw in

4.3.7.3

Hose connections

Proceed as follows:

• Visual inspection

Check:

– Oil leaks from hoses and couplings
– Couplings for damage and contamination
– Hoses for damage

• Push the hose coupling on to its counterpart until you hear it "click"

• Twist the locking ring of the coupling

Information

If hoses cannot be connected or are difficult to connect, they are under
pressure. Depressurise the hoses by means of the pressure relief
device.

Never use force to connect couplings!

Information

Connect the hose couplings with angle pieces to the wire saw SK-SD.
Connect the straight hose couplings to the drive unit.

Содержание SK-SD



































































Результаты поиска

Содержание SK-SD

Отзывы:

Похожие инструкции для SK-SD

Бренды по названию

Популярные бренды

TYROLIT Hydrostress SK-SD, Инструкция по эксплуатации и запасные части

Результаты поиска

Содержание SK-SD

Отзывы:

Похожие инструкции для SK-SD

Бренды по названию

Популярные бренды