Tymetal Corp. TYM-VSA, Инструкция по установке и эксплуатации, Страница: 3 / 36

TYM-VS2 Slide Gate Operator Installation Guide
- 1 -
Revision 0, 072012
- 1 -
Before You Begin...
Before unpacking, inspect the carton for exterior damage.
claim. Inspect your package carefully. You can check your
accessory box parts with the enclosed packing slip for your
convenience. Claims for shortages will be honored for only
30 days from the date of shipment.
If you have any questions about the requirements for proper
installation of this gate operator contact technical support at
800-328-4283.
Always Check the Gate’s Action
It’s very important before installing the gate operator
to make sure the gate slide is free and level throughout
the entire opening distance. If the gate does not seem to
operate properly, it may affect the operator performance
or greatly shorten the life of the unit.
All gate operators can be divided into one of four different
this gate operator only when the operator is appropriate for
• Class I Residential Vehicular Gate Operator
A vehicular gate operator intended for use in a home or for one
to four single family dwellings with a common garage or parking
area associated with these dwellings.
• Class II Commercial / General Access Vehicular Gate Operator
A vehicular gate operator intended for use in a commercial
or more single family units, hotel, retail store or other building
servicing the general public.
• Class III Industrial / Limited Access Vehicular Gate Operator
A vehicular gate operator intended for use in an industrial
location or building such as a factory or loading dock area or
other location not intended to service the general public.
• Class IV Restricted Access Vehicular Gate Operator
A vehicular gate operator intended for use in a guarded industrial
location or building such as an airport security area or other
restricted access locations not servicing the general public,
in which unauthorized access is prevented via supervision by
security personnel.
Approved Obstruction Detection Devices
The following contact or non-contact obstruction detection
devices have been approved for use with this slide gate
operator as part of a UL325 compliant installation:
• Contact Edges
Miller Edge Models MGO20, MGR20, MGS20, ME120
• Photoeyes
MMTC Model IR-55 (165’ range - P/N 2520-441)
MMTC Model E3K (28’ range - P/N 2520-031)
Regulatory Warnings
Read the following before beginning to install this slide gate
operator:
THE FOLLOWING FORMATS ARE USED FOR SAFETY
NOTES IN THESE INSTRUCTIONS.
WARNING
This type of warning note is used to indicate possible
mechanical hazards that may cause serious injuries or
death.
CAUTION
This type of warning note is used to indicate the possibility
of damage to the gate or gate operator.
WARNING
This type of warning note is used to indicate possible
electrical shock hazards that may cause serious injuries or
death.
WARNING
1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.
2. Read the yellow “Safety Instructions” brochure enclosed
with the packet of information. If any pages are missing or
are unreadable, or you do not have the safety instructions,
please call Tymetal at 1-800-328-4283 to request additional
copies.
3. ALL ELECTRICAL CONNECTIONS TO THE POWER
SUPPLY MUST BE MADE BY A LICENSED ELECTRICIAN
AND MUST OBSERVE ALL NATIONAL AND LOCAL
ELECTRICAL CODES.
4. A separate power-disconnect switch should be located near
the operator so that primary power can be turned off when
necessary.
5. Install the enclosed warning signs on both sides of the gate.
A minimum of two (2) WARNING SIGNS shall be installed,
one on each side of the gate where easily visible.
6. Never reach between, through or around the fence to
operate the gate.
7. Never connect a button station within reach of the gate or on
the side of the gate operator.
8. Do not adjust the operator controller’s current sensing
feature too high. It should be adjusted high enough to keep
the gate from falsely triggering the sensing, but no higher
than necessary for the gate to operate. DO NOT DEFEAT
THE PURPOSE OF THIS FUNCTION!
9. You must install all required safety equipment.
10. UL325 Compliance requires the use of contact edges or
photoelectric controls on all automatic or remotely-controlled
gate operators.
11. The operator is intended for installation only on gates used
for vehicles. Pedestrians must be supplied with a separate
access opening. The pedestrian access opening shall be
designed to promote pedestrian usage. Locate the gate such
that persons will not come into contact with the vehicular
gate during the entire path of travel of the vehicular gate.