TYM TX1500 Скачать руководство пользователя страница 176

Страница: 176 / 218

7 -

TROUBLESHOOTING

1. ENGINE SYSTEM

TROUBLE

PROBaBLE CaUSE

SOLUTION

Engine

The start motor does

not run even when

turning the main

switch.

Battery discharged

•

Charge the battery

•

No power supplied due to power

cut-off

•

Check the fuse and connector

•

Loose terminal

•

Check for looseness and corrosion. Clean, tighten and ap-

ply grease

•

Faulty switch

•

Have it repaired or replaced by workshop

•

Defective start motor

•

Have it repaired or replaced by workshop

•

The start motor runs

but its speed cannot

be increased

Weak battery

•

Charge the battery

•

Poor ground

•

Clean the contact and connect the ground firmly

•

Incorrect viscosity of engine oil

•

Change engine oil with proper viscosity

•

The start motor runs

but the engine cannot

be started

Air in fuel system

•

Bleed the system

•

Clogged fuel filter

•

Clean or replace the filter

•

Defective engine

•

Have it repaired by workshop

•

Defective key stop unit

•

Have it repaired by workshop

•

The engine runs irreg-

ularly

Air in fuel system

•

Bleed the system

•

Clogged fuel filter

•

Clean or replace the filter

•

Clogged injection nozzle

•

Have it repaired by workshop

•

Damaged turbocharger or its inlet

•

Check the inlet/outlet duct and turbocharger

•

TX1500-영문-07(사).indd 2

2012-12-17 오후 2:28:39

Содержание TX1500



























































































































































































































Результаты поиска

Содержание TX1500

Отзывы:

Похожие инструкции для TX1500

Бренды по названию

Популярные бренды

TYM TX1500, Руководство пользователя

Результаты поиска

Содержание TX1500

Отзывы:

Похожие инструкции для TX1500

Бренды по названию

Популярные бренды