background image

Tomcat i875PF S5105 

                                                                                User’s Manual                     

 

 

http://www.tyan.com

 

 

 
 

 

 

Tomcat i875PF 

/// 

S5105 

 

Revision 1.00

 

 

 

Copyright © TYAN Computer Corporation, 2003.  All rights reserved.  No part of this manual 
may be reproduced or translated without prior written consent from TYAN Computer Corp. 
 
 
All registered and unregistered trademarks and company names contained in this manual are 
property of their respective owners including, but not limited to the following. 
 
TYAN, Tomcat, i875PF and S5105 are trademarks of TYAN Computer Corporation. 
Intel, Pentium 4, and combinations thereof are trademarks of Intel Corporation. 
Award, AwardBIOS are trademarks of Award Software Incorporated. 
Microsoft and Windows are trademarks of Microsoft Corporation. 
IBM, PC, AT and PS/2 are trademarks of IBM Corporation. 
ATI, ATI RAGE is a trademark of ATI Technologies Incorporated. 
Winbond is a trademark of Winbond Electronics Corporation. 
Portable Document Format (PDF) is a trademark of Adobe Corporation. 
 
 
 
Information contained in this document is furnished by TYAN Computer Corporation and has 
been reviewed for accuracy and reliability prior to printing.  TYAN assumes no liability 
whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of 
TYAN products including liability or warranties relating to fitness for a particular purpose or 
merchantability.  TYAN retains the right to make changes to product descriptions and/or 
specifications at any time, without notice. In no event will TYAN be held liable for any direct or 
indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting 
from errors or inaccuracies of information contained in this document. 

 

Содержание S5105
















































































Отзывы: