TYAN S2725 Скачать руководство пользователя страница 32

Страница: 32 / 52

http://www.TYAN.com

3.4 – Floppy Configuration

Options related to floppy drives can be altered through the following.

Floppy A
Floppy B

360KB, 5 ¼”
1.2MB, 5 ¼”
720KB, 3 ½”

1.44MB, 3 ½”

2.88MB, 3 ½”
Disabled

Defines the floppy drive type.

3.5 – Boot Settings Configuration

Options related to startup settings can be altered through the following.

Quick Boot

Enabled

Disabled

When set to Enabled, some self-tests will be skipped
during POST.

Quiet Boot

Enabled

Disabled

If set to Enabled, OEM logo will be displayed instead
of POST messages.

Add-On Rom

Display Mode

Force BIOS

Keep Current

Leave as Default. This setting toggles the Add-On
ROM video display mode.

Boot up Num-Lock

Off

Specifies whether Num-Lock will be on or off during
bootup.

PS/2 Mouse

Support

Enabled

Disabled

Toggles the use of the PS/2 mouse port.

Typematic Rate

Fast

Slow

Changes speed of key repeat rate.

System Keyboard

Present

Unavailable

Will allow continual boot even if the keyboard is not
attached.

Parity Check

Enabled

Disabled

Toggles checking of system memory for corruption.

Wait for F1 if “error”

Enabled

Disabled

If Enabled, you will have to press F1 for the system
to continue booting if an error is detected during
POST.

Hit “Del” Message

Enabled

Disabled

Toggles display of pressing DEL key to enter BIOS.

Interrupt 19 capture

Enabled

Disabled

This option allows removable devices to act as non-
removable devices. Some SCSI RAID cards will
need this one enabled. Please refer to your SCSI
card’s manual.

Primary Display

Device

Auto

Onboard VGA

Change settings to alow dual monitor support

Содержание S2725





















































Результаты поиска

Содержание S2725

Отзывы:

Похожие инструкции для S2725

Бренды по названию

Популярные бренды

TYAN S2725, Руководство пользователя

Результаты поиска

Содержание S2725

Отзывы:

Похожие инструкции для S2725

Бренды по названию

Популярные бренды