TYAN S2725 Скачать руководство пользователя страница 33

Страница: 33 / 52

http://www.TYAN.com

3.6 – Super IO Configuration

Options related to the IO interface can be altered through the following.

Serial Port 1, 2

Address

COM1
Enabled

Disabled
Auto
COM2
Enabled

Disabled

Auto

Toggles use of serial ports 1 and or 2 (com1 & 2).

Enabling

ports also requires you to enter the I/O

address for that port unless you select

Auto

Parallel Port Address

Disabled

3F8, 2F8
3E8, 2E8

These options are dependent on the IRQ and vice
versa.

Output Only

Standard one-way protocol for parallel devices.

Bi-directional

Two-way protocol

EPP

Enhanced Parallel Port may provide higher
bandwidth if an

EPP

compliant device is

Parallel Port Mode

ECP

Enhanced Compatibility Port may provide higher
bandwidth if an

ECP

compliant device is

Parallel Port

IRQ

IRQ 7
IRQ 5

Sets the interrupt request for the parallel port.
(IRQ 7 and IRQ 5 both can be defaults.)

3.7 – Onboard Device Configuration

Options related to onboard devices can be altered through the following.

Onboard ATI RageXL

Video

Enabled

Disabled

Toggles the onboard ATI video graphics.

Onboard 10/100 LAN

Enabled

Disabled

Toggles 10/100Mbit LAN port.

Onboard Gigabit LAN #1

Enabled

Disabled

Toggles the 1Gbit LAN port.

Onboard Gigabit LAN #2

Enabled

Disabled

Toggles the 1Gbit LAN port.

3.8 – USB Configuration

Options related to USB can be altered through the following.

USB Function

2 USB ports

, 4 USB

ports,

6 USB ports, 8

USB Ports

Toggles the onboard USB ports.

USB 2.0 Controller

Enabled

Disabled

Legacy USB Support

Enabled
Disabled

Auto

Toggles the use of onboard USB ports
in DOS.

USB Zip Emulation Type

Enabled
Disabled

Auto

Toggles Zip drive emulation on USB
ports when in use.

USB Beep Message

Enabled

Disabled

Toggles USB beep error messaging.

Содержание S2725





















































Результаты поиска

Содержание S2725

Отзывы:

Похожие инструкции для S2725

Бренды по названию

Популярные бренды

TYAN S2725, Руководство пользователя

Результаты поиска

Содержание S2725

Отзывы:

Похожие инструкции для S2725

Бренды по названию

Популярные бренды