Tuthill SDV Series Скачать руководство пользователя страница 19

Страница: 19 / 58

Manual 1861 Rev C p/n 001861 0000

LOCATION

Mount the pump on a base frame with sufficient

rigidity, placed on a flat and level surface. If the

pump will be installed outdoors, check the motor,

exterior paint, peripheral equipment, and other

parts for outdoor service suitability.

Allow enough space surrounding the pump

for access during maintenance and periodic

inspections.

FOUNDATION

Make sure the foundation for the pump assembly

and its base frame is flat and leveled with adequate

load bearing capacity.

Install the pump and its base frame, peripheral

equipment, and piping when the fountation

concrete has been cured.

PUMP INSTALLATION

Always operate SDV pumps in a horizontal and

level position on a rigid base frame. Never install

SDV pumps in an upright (vertical) or angled

position.

1. Place the pump assembly with the base frame

on a foundation and make sure it is supported

evenly.

2. Insert metal shims between the base frame

and the foundation, if required for leveling. The

pump assembly with the base frame should be

leveled to within 0.02 in. in any 3.28 ft (0.5 mm

in any 1 m).

3. Place adequately sized anchorbolts in position.

4. Once the pump assembly is set on the

foundation and anchorbolts, adequately

grout the base frame before tightening the

anchorbolt nuts. Tigten the anchorbolt nuts

after the grout is firmly cured.

OTE:

Tighten the anchorbolts evenly to ensure

the previously set level is not changed.

PIPING

Main Piping Assembly

1. Clean the interior of the process piping to

remove any rust, dust, foreign matter, and weld

slags.

2. Place a 40-mesh strainer, supplied along with

the SDV pump, at the pump process inlet

flange. After initial start-up and continued

operation of the SDV pump for several hours,

disassemble the process inlet piping from the

pump and check the strainer for cleanliness.

If there are any particulates strained, such as

weld slags, etc., clean the mesh strainer and

replace it at the pump process inlet flange.

OTE:

Tuthill recommends regularly checking

the condition of the strainer.

INSTALLATION

Содержание SDV Series



























































Результаты поиска

Содержание SDV Series

Отзывы:

Tuthill SDV Series, Руководство оператора, Страница: 19 / 58

Результаты поиска

Содержание SDV Series

Отзывы: