manualshive.com logo in svg

Tuthill KINNEY KC Series, Руководство оператора, Страница: 25 / 48

Поделиться
Скачать
Tuthill KINNEY KC Series Скачать руководство пользователя страница 25

19

06

Troubleshooting

Manual 1807 Rev B p/n 001807 0000

SYMPTOM

PROBABLE CAUSE

REMEDIES

Pump stalls

Electrical power loss

Check power at the pump.

Pump malfunctioning

Contaminated pump 

oil or insufficient 

lubrication

See Stalling on page 17

. 

See V-Belt on page 7

 

and 

Changing the Oil on page 14

.

Blocked pump 

discharge line

Clear the pump discharge line. Check the oil mist 

eliminator element for blockage.

Pump will not start

Electrical failure

Check for power at the pump. Check the motor start 

controls and motor.

Pump flooded with oil

Clear oil from the pump by turning over by hand or 

disassembling the pump. 

See Flooding on page 15

.

Excessively low 

temperature

Heat the pump to minimum starting temperature of 

50°F (10°C).

Oil discharged from oil 

mist eliminator

Excess oil on discharge 

side of oil mist 

eliminator

Unscrew the oil mist eliminator and pour oil through the 

discharge fitting back into the pump.

Reduce pump inlet pressure below 10 Torr to allow 

collected oil to drain back through the integral check 

valve in the oil mist eliminator.

Table 6-1– Common Symptoms and Remedies

CHECKING PUMP PERFORMANCE

If the processing time increases or the ultimate 

pressure becomes poor with no recent changes 

in the process or in the system configuration, test 

the pump to determine whether the trouble is in 

the pump or the connected process equipment. To 

check the condition of the pump, use a McLeod 

gauge to measure the blank-off pressure as 

described in the following procedure.

OTEE:  

N

If possible, also read the blank‑off 

pressure with a thermistor or 

thermocouple gauge. See 

Figure 6-1

 and 

Table 6-1

 for common faults in vacuum 

systems.

Figure 6-1 – Pump Test Manifolding

To read the pump blank-off pressure:

1. Close off the pump inlet by means of a vacuum

valve or short segment of manifolding, as

shown in 

Figure 6-1

.

2. Connect a vacuum gauge to the pump side of

the valve or manifolding. Position the gauge

connection so that it will not become flooded or

blocked by splashing pump oil.

Содержание KINNEY KC Series

















































Отзывы:

Нет отзывов