Tuthill KINNEY 850D Скачать руководство пользователя страница 13

Страница: 13 / 38

5.4.2 HAZARDS ASSOCIATED WITH HAZARDOUS PROCESS FLUIDS

DANGER

It shall be the responsibility of the installer to ensure that piping is adequate,

sealing between pipe joints is adequate for the process fluids and proper

process and pressure protection devices are in place. It is also the

responsibility of the installer to assure that process gasses are not vented

in a manner that would be hazardous. Refer to the manufacturer of the

process media to assure that proper safety precautions are in place.

5.4.3 COOLING WATER

The cylinder cooling water jacket is shipped dry. Fill the water jacket before starting the pump.

If an optional water flow modulating valve (Water Miser) is fitted, the cylinder may take 20 minutes or more

to fill. The delay can be avoided by lifting the spring to open the valve. For installation of the valve see

Figure 6.

Failure to ensure that the cooling water jacket is filled before starting the pump will result in localized over-

heating of the pump and cause extensive damage.

For installations requiring starting at ambient temperatures lower than 60°F (16°C), electric heaters should

be installed in the water jacket with an optional temperature switch installed in the separator housing. (see

Figure 5)

WARNING

Do not allow the cooling water to freeze in the pump.

Freezing of the cooling water jacket usually results in extensive damage to the pump cylinder which cannot

be repaired.

Connect a water supply line with “on-off” valve to the water inlet, and an open drain to the water outlet. The

inlet line should have a flow regulating valve. If the water supply is unreliable, it is advisable to install a flow

switch to stop the pump or signal when the flow is interrupted. Normally the cooling water will be off when

the pump is not running.

Содержание KINNEY 850D







































Результаты поиска

Содержание KINNEY 850D

Отзывы:

Похожие инструкции для KINNEY 850D

Бренды по названию

Популярные бренды

Tuthill KINNEY 850D, Руководство оператора

Результаты поиска

Содержание KINNEY 850D

Отзывы:

Похожие инструкции для KINNEY 850D

Бренды по названию

Популярные бренды