Tuthill 1200 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 64

Tuthill 1200 Скачать руководство пользователя страница 32

26

Manual 2003 Rev D p/n 2003

GENERAL

Regular inspection of the vacuum booster and

its installation, along with complete checks on

operating conditions, will pay dividends in added

life and usefulness. Also, service the drive

per manufacturer’s instructions and lubricate

the coupling or check belt drive tension. Use

thermometers and gauges to make sure that

booster operating temperature and pressure

remain within allowed limits.

DANGER

!

The booster and parts may
contain hazardous media.
Assure that pump and parts are
evacuated of hazardous media
prior to servicing.

CAUTION

!

The electrical service must be isolated and
de-energized prior to maintenance. Apply
appropriate procedures to assure electrical
supply is de-energized and cannot be
inadvertently energized during maintenance.
Assure piping and product is isolated prior to
maintenance of booster. Apply appropriate
procedures to assure piping and product is
isolated and that inadvertent opening of valves
cannot occur during maintenance.

CAUTION

!

During routine maintenance, inspect and assure
that guards are in place and secure.

When changing oil, be sure to reseal the drain

and fill plugs. This is especially important on

Slinger Splash Lube Series models, which

have no mechanical seals on the rotors. Air

leaks past these plugs can cause rapid loss of

oil from end covers, resulting in booster failure.

Pay special attention to lubrication of timing gears

and bearings according to the information in

Lubrication on page 14

.

When a vacuum booster is taken out of service, it

may require internal protection against rusting or

corrosion. The need for such protection must be

a matter of judgment based on existing conditions

as well as length of downtime. Under atmospheric

conditions producing rapid corrosion, protect the

booster immediately.

See Long-Term Storage on

page 28

.

MAINTENANCE

07

«
...
30
31
32
33
34
...
»

Содержание 1200

































































Отзывы:

Нет отзывов