Turner 2180-000 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 21

background image

Turbidity Plus Sensor

998-2187

Rev. G

Page 4

1.

Introduction

1.1 Description

Turbidity Plus

TM

is an accurate single-channel turbidity sensor with an

integrated, user-controlled wiper motor.  It is designed for integration with
multiparameter systems and dataloggers from which it receives power and wiper
motor triggers at user-defined intervals.  Turbidity Plus is available in two linear
ranges up to 500 or 3,000 NTU with minimum detection limits of 0.05 or 0.5 NTU
respectively.  It delivers a voltage response proportional to the turbidity of the
sample which can be correlated to nephelometric turbidity unit (NTU)
concentrations by calibrating the sensor using AMCO Clear Turbidity Standards.
Deployable to 200 meters, Turbidity Plus is available in a variety of
configurations to facilitate integration.

«
...
2
3
4
5
6
...
»

Содержание 2180-000






















Отзывы:

Нет отзывов

Похожие инструкции для 2180-000

Бренд: QUIETON Страницы: 24

Бренд: Quest Engineering Страницы: 24

Бренд: Nauticam Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: Hama Страницы: 2

Бренд: Abicor Binzel Страницы: 8

Бренд: Banner Страницы: 12

Бренд: Valore Страницы: 5

Бренд: Parker Страницы: 2

Бренд: Park Tool Страницы: 2

Бренд: ParaZero Страницы: 17

Бренд: quadient Страницы: 2

AcousticDesign AD-S52

Бренд: QSC Страницы: 4

Бренд: Waterpik Страницы: 20

Water Flosser WF-06

Бренд: Waterpik Страницы: 2

Бренд: Waterpik Страницы: 6

Бренд: Waterpik Страницы: 24

QuadraTop Adventure Top S

Бренд: Quadratec Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды