Turner 2180-000 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 21

Turner 2180-000 Скачать руководство пользователя страница 14

Turbidity Plus Sensor

998-2187

Rev. G

Page 14

5.

Maintenance and Warranty

5.1 Maintenance

5.1.1 Rinsing

Turbidity Plus should be rinsed or soaked in fresh water following each
deployment, ideally, until it is completely clean again.

5.1.2 Care for the bulkhead connector

A light coat of Silicone spray should be used on the rubber of the male
pins of the bulkhead to aid in sealing. The manufacturer recommends
3M™ Silicone Lubricant Spray or Loctite 8021 spray.

Note: You should avoid using silicone grease. Do NOT use WD-40,

it will destroy the connectors.

Note: Turbidity Plus should

NOT

come in contact with any organic

solvents (i.e. acetone, methanol) or strong acids and bases.

5.2 Warranty Terms

Turner Designs warrants Turbidity Plus and accessories to be free from defects
in materials and workmanship under normal use and service for a period of 12
months from the date of shipment from Turner Designs with the following
restrictions:



Turner Designs is not responsible for replacing parts damaged by

accident or neglect.  Your instrument must be installed according to
instructions in the User’s Manual.  Damage from corrosion is not
covered.  Damage caused by customer modification of the instrument is
not covered.



This warranty covers only Turner Designs products and is not extended

to equipment used with our products. We are not responsible for
incidental or consequential damages, except in those states where this
limitation is not allowed. This warranty gives you specific legal rights and
you may have other rights which vary from state to state.



Damage incurred in shipping is not covered.

5.3 Warranty Service

To obtain service during the warranty period, the owner shall take the following
steps:

1. Write, email or call Turner Designs Technical Support and describe as

precisely as possible the nature of the problem.

«
...
12
13
14
15
16
...
»

Содержание 2180-000






















Отзывы:

Нет отзывов