Turner 2180-000 Скачать руководство пользователя страница 17

Страница: 17 / 21

Turbidity Plus Sensor

998-2187

Rev. G

Page 17

Appendix A: Specifications

*Accuracy is

determined by the user’s correlation between the 0-5 V output and the 0-3000

NTU range. Resolution is determined by the datalogger. Turbidity Plus are not factory
calibrated.

Parameter

Specification

Power Draw

@ 12V: Max 140mW (180mW for 500NTU) signal only

@ 12V: Typical 230mW (280mW for 500NTU) while wiper
rotates.
Power draw increases if there is resistance to the wiper.

Input Voltage

3 - 15 VDC

Signal Output

Single gain, 0

– 5 VDC Analog

3000 NTU

500NTU

MDL

0.5 NTU

0.05 NTU

Range

0-3000 NTU*

0-500 NTU*

Precision

– 10 (± 0.1 NTU)

– 1000 (± 0.4 NTU)

> 1000 (± 0.04% of NTU
Concentration)

0-50 NTU (± 0.05 NTU)
50-500 NTU (± 0.25 NTU)

Linearity (full range)

0.99 R

Wiper Trigger

Pulse to zero (ground) for wiper rotation

Minimum Pulse Width for Wiper

Trigger

50 milliseconds

Temperature Range

Ambient: 0 to 50



Water Temp: -2 to +50



Light Source

Light Emitting Diode

Excitation Wavelength

Detector

Photodiode

Settling time from power on

= < 3 seconds

Housing Material -

Delrin

Dimensions -

– Housing only: 4.35 in., 11.05 cm

L - Housing with connector and wiper: 6.10 in., 15.49 cm;
D: 1.185 in., 3.01 cm

Depth Rating

200 meters

Weight with Connector and Wiper

4.9 oz; 138 gm

Sampling focal point is in front of the sensor face

No data averaging - analog signal output

Содержание 2180-000






















Результаты поиска

Содержание 2180-000

Отзывы:

Похожие инструкции для 2180-000

Бренды по названию

Популярные бренды

Turner 2180-000, Руководство пользователя

Результаты поиска

Содержание 2180-000

Отзывы:

Похожие инструкции для 2180-000

Бренды по названию

Популярные бренды