Turf Equipment Z-AERATE Скачать руководство пользователя

Страница: 43 / 48

Troubleshooting

Important:

It is essential that all operator safety mechanisms be connected and in proper operating

condition prior to use.

When a problem occurs, do not overlook the simple causes. For example: starting problems could be caused
by an empty fuel tank.

The following table lists some of the common causes of trouble. Do Not attempt to service or replace major
items or any items that call for special timing of adjustments procedures (such as valves, governor, etc.). Have
this work done by your

Engine Service Dealer

Note:

When disconnecting electrical connectors Do Not pull on the wires to separate the connectors.

Problem

Possible Cause

Corrective Action

1. Battery does not have a full charge.

1. Charge the battery. See

Check Battery

Charge

and

Recommended Jump

Starting Procedure

sections in

Maintenance.

2. Electrical connections are corroded, loose

or faulty.

2. Check the electrical connections for

good contact. Clean connector terminals
thoroughly with electrical contact cleaner,
apply dielectric grease and reconnect.

3. Fuse is blown.

3. Replace the blown fuse.

Starter does not crank.

4. Relay or switch is defective.

4. Contact an Authorized Service Dealer.

1. Fuel tank is empty.

1. Fill the fuel tank.

2. The throttle and choke are not in the

correct position.

2. Be sure the throttle control is midway

between the “SLOW” and “FAST”
positions, and the choke is in the “ON”
position for a cold engine or the “OFF”
position for a warm engine.

3. Dirt in fuel filter.

3. Replace the fuel filter.

4. Dirt, water, or stale fuel is in the fuel

system.

4. Contact an Authorized Service Dealer.

5. Air cleaner is dirty.

5. Clean or replace the air cleaner element.

6. Electrical connections are corroded, loose

or faulty.

6. Check the electrical connections for

good contact. Clean connector terminals
thoroughly with electrical contact cleaner,
apply dielectric grease and reconnect.

7. Relay or switch is defective.

7. Contact an Authorized Service Dealer.

8. Faulty spark plug.

8. Clean, adjust or replace spark plug.

Engine will not start, starts hard, or fails to
keep running

9. Spark plug wire is not connected.

9. Check the spark plug wire connection.

1. Engine load is excessive.

1. Reduce the ground speed or aeration

depth.

2. Air cleaner is dirty.

2. Clean or replace the air cleaner element.

3. Oil level in the crankcase is low.

3. Add oil to the crankcase.

4. Cooling fins and air passages for the

engine are plugged.

4. Remove the obstructions from the

cooling fins and air passages.

5. Dirt in fuel filter.

5. Replace the fuel filter.

Engine loses power.

6. Dirt, water, or stale fuel is in the fuel

system.

6. Contact an Authorized Service Dealer.

1. Engine load is excessive.

1. Reduce the ground speed or aeration

depth.

2. Oil level in the crankcase is low.

2. Add oil to the crankcase.

Engine overheats.

3. Cooling fins and air passages for the

engine are plugged.

3. Remove the obstructions from the

cooling fins and air passages.

Содержание Z-AERATE

















































Результаты поиска

Содержание Z-AERATE

Отзывы:

Похожие инструкции для Z-AERATE

Бренды по названию

Популярные бренды

Turf Equipment Z-AERATE, Руководство оператора

Результаты поиска

Содержание Z-AERATE

Отзывы:

Похожие инструкции для Z-AERATE

Бренды по названию

Популярные бренды