TuffStuff SP-401 Скачать руководство пользователя страница 8

Страница: 8 / 11

FIG. 21

Affix the

Weight Shroud (#2)

to the bottom of the

Weight

Stack Frame (#1)

and at the top of the

Guide Rod Retainer (#5)

us-

ing four Hex Head Cap Screws 1/4-20 X 3/4 (#21), and four Flat
Washers 1/4” (#20).

FIG. 22

Insert the two Plastic Shroud Edge Protectors (#12) to both

Shrouds (#2, #3)

, in the position as shown above, and slide them all

the way down.

CABLE ADJUSTMENT

It is imperative that you maintain proper cable adjustment to ensure
a safe and smooth operation.

Caution:

The Cable should be inspected and adjusted peri-

odically to avoid any slack in the cable which would, conse-
quently, prevent any damage to the equipment or personal
injury.

Cable Adjustment

1. Loosen the Finished Hex Nut 1/2-13 (#59).
2. Thread the Cable Hex Tap Bolt 1/2-13 X 3 (#56) in or out

of the threaded socket of the

Top Plate Selector Bar (#9)

to give the

Cable (#38)

proper tension.

3. Re-tighten the Finished Hex Nut 1/2-13 (#59) to complete

the adjustment.

Caution:

Make sure the Cable Hex Tap Bolt 1/2-13

X 3 (#56) is threaded at least 1/2” into the threaded
socket of the

Top Plate Selector Bar (#9)

once the

cable adjustment has been completed.

SP-401 Supine Bench Press

Содержание SP-401












Результаты поиска

Содержание SP-401

Отзывы:

Похожие инструкции для SP-401

Бренды по названию

Популярные бренды

TuffStuff SP-401, Руководство по сборке

Результаты поиска

Содержание SP-401

Отзывы:

Похожие инструкции для SP-401

Бренды по названию

Популярные бренды