background image

DO NOT DISCARD THIS MANUAL  

TASK INDUSTRIES, INC.

 

1325 E. Franklin Ave., Pomona, CA 91766 

Ph: 909-629-1600 Fax: 909-629-4967 

E-mail: [email protected]  Net: www.tuffstuff.net 

L I M I T E D   W A R R A N T Y  

TuffStuff warrants to the original purchaser only that TuffStuff equipment will be free from defects in 
material and workmanship.  The warranty and remedies set forth herein are conditioned upon proper 
storage, installation, use, maintenance and conformance with any recommendations of TuffStuff.  This 
warranty does not cover products not manufactured by TuffStuff or products which are altered without 
the express written consent of TuffStuff.  This warranty as specified:  a) Frame structure and welds — 
Lifetime, b) Moving parts (e.g. pulleys, bearings, bushings)  — 5 years; c) Cables upholstery, hand-
grips, finish and any miscellaneous parts not listed — 1 year; from the day of delivery to the original 
purchaser.  The obligation of TuffStuff under this warranty is limited to repairing or replacing warranted 
defective parts, as TuffStuff may elect, at TuffStuff’s facility in Pomona, California, without charge to 
purchaser for either parts or labor.  Purchaser is responsible for  installation of repaired or replaced 
parts, and all transportation and insurance costs on returned or replaced equipment to and  from 
TuffStuff’s facility in Pomona. 

 

THE FORGOING SHALL CONSTITUTE THE SOLE REMEDY OF THE PURCHASER AND THE 
SOLE LIABILITY OF TUFFSTUFF WITH REGARD TO WARRANTY.  NO IMPLIED STATUTORY 
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL AP-
PLY.  IN NO EVENT, WHETHER AS A RESULT OF BREACH OF CONTRACT, WARRANTY, NEG-
LIGENCE OR OTHERWISE, SHALL TUFFSTUFF BE LIABLE FOR SPECIAL, INCIDENTAL OR 
CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO,  LOSS OF PROFITS OR 
REVENUE, LOSS OF USE OF EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTION 
EQUIPMENT, DOWNTIME COST, OR CLAIMS OF CUSTOMERS OR PURCHASER FROM SUCH 
DAMAGE. 

 

This warranty is the final, complete and exclusive agreement of the parties with respect to the quality 
or performance of the equipment and no action for breach of this written warranty or any implied war-
ranty shall be commenced more than one (1) year after the accrual of the cause of action.  No modifi-
cation of this warranty or waiver of its terms shall be binding on either party unless approved in writing 
by an authorized representative of the party.  Contact TuffStuff at 1325 E. Franklin Avenue, Pomona, 
California 91766, before returning any defective equipment. 

Note:

  Retain your sales receipt and be sure to mail in the warranty registration card to insure that a 

permanent record of your purchase is on file with the factory and to avoid unnecessary delays in 
warranty service.

 

Содержание SP-401












Отзывы: