manualshive.com logo in svg

TSI Incorporated Certifier FA Plus, Руководство оператора

Поделиться
Скачать
TSI Incorporated Certifier FA Plus Скачать руководство пользователя страница 47

 

 

37

 

3

  Troubleshooting 

Table 4

 

lists the symptoms, possible causes, and recommended corrective actions for 

problems you may encounter with the Certifier

®

 FA Test System. If the symptom is not 

listed, or if none of the recommended corrective actions solve the problem, please visit 
our website at 

http://service.tsi.com

 or contact TSI Customer Support at (800) 874-2811 

or 651-490-2811.  

 

Table 4. Troubleshooting the Certifier

®

 FA Test System 

Symptom 

Possible Cause 

Corrective Action 

Interface Module 

won’t 

turn on, or turns on 
and off. 

Batteries are depleted or 
not installed. 

Connect AC adapter or install 
charged batteries. 

Measurements are not 
displayed even though 
Interface Module is 
turned on. 

Flow module is not 
connected to Interface 
Module. 

Connect flow module to Interface 
Module. If connected, disconnect 
and then reconnect. 

Measurements are not 
changing or graph is 
not updating. 

Pause 

 button was 

pressed. 

Press the 

Play

 

 button at the 

top of the screen.  

“OOR” is shown on 
display. 

Measurement is out of 
range. 

Check range for displayed 
measurement, and only make 
measurements within that range. 

Flow rate does not 
read zero when no gas 
flowing (Especially 
when set to N

2

O or 

CO

2

). 

Meter was not purged 
with gas displayed on the 
Interface Module. 

Purge meter with gas displayed 
on Interface Module or press gas 
select key to change to desired 
gas. 

Unable to disconnect 
flow module from 
Interface Module. 

Pulling on the cable 
rather than the connector. 

Pull the locking connector (not 
the cable) to disengage 
connector lock.  

Содержание Certifier FA Plus
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды