TSC TTP-245 series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 41

TSC TTP-245 series Скачать руководство пользователя страница 32

27

5. Maintenance

5.1 Cleaning

Use one or more of the following supplies that meets your needs:

Cotton swab

Lint-free cloth

Vacuum

100%

ethanol

The cleaning process is described as following

Printer Part

Method

Printer Head

1. Always turn off the printer before cleaning the print

head.

2. Allow the printhead to cool for a minimum of one

minute.

3. Use a cotton swab and 100% ethanol to clean the
print head surface.

Platen Roller

1. Turn the power off.

2. Rotate the platen roller and wipe it thoroughly with
100% ethanol and a cotton swab, or lint-free cloth.

Exterior

Wipe it with water-dampened cloth.

Interior

Brush or air blow.

Note:

Do not touch printer head by hand. If you touch it careless, please use ethanol to
clean it.

It’s industry alcohol. Please do not use regular alcohol, which may damage the
printer head.

You may have to clean the supply sensors more often if you frequently receive
supply error messages.

«
...
30
31
32
33
34
...
»

Содержание TTP-245 series










































Отзывы:

Нет отзывов