TSC TTP-244CE series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 33

background image

TTP-245C/ TTP-343C/ TTP-244CE
Bar Code Printer Service Manual

20

3.8 Peel-off Module Installation (Option)

1. Refer to section 3.2 to remove the lower cover.

2. Open the top cover and pull up the front panel from the printer. Thread the 5-pin peel-off

module harness through the front slot of lower inner cover.

3. Plug in the peel-off module harness connector to the 5-pin red socket on the main board.

4. Embed the tenons into the both sides mortise of lower inner cover and close the peel-off

cover.

Front panel

Peel-off module
harness

Slot

5-pin socket

Peel-off module

«
...
20
21
22
23
24
...
»

Содержание TTP-244CE series


































Отзывы:

Нет отзывов

Похожие инструкции для TTP-244CE series

Бренд: NAFVJGS Страницы: 131

Бренд: Metrologic Страницы: 33

Skylark WMU2000

Бренд: Alien Страницы: 28

Бренд: Duali Страницы: 12

ACR1281U-C1 Dualboost 2

Бренд: ACS Страницы: 16

Бренд: Sirit Страницы: 108

POWERSCAN PBT7100 guide

Бренд: Datalogic Страницы: 352

Бренд: Unitech Страницы: 117

Бренд: Kyungwoo Страницы: 7

Fastmark M9 Plus

Бренд: AMT Datasouth Страницы: 70

Fastmark M10XPd/Gen-2

Бренд: AMT Datasouth Страницы: 72

EZ6000 Plus Series

Бренд: Godex Страницы: 2

Бренд: Quatech Страницы: 2

Бренд: Cypress Страницы: 16

Бренд: ALTUS Страницы: 2

DL Cordless Card

Бренд: Datalogic Страницы: 55

Бренд: Datalogic Страницы: 119

Бренд: Datalogic Страницы: 203

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды