TSC TTP-244CE series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 33

background image

TTP-245C/ TTP-343C/ TTP-244CE
Bar Code Printer Service Manual

11

3. MECHANISM

Please turn off the power switch and unplug the power adapter before replacing parts.

3.1 Replacing Top Cover and Media View Window Cover

1. Turn the printer upside down and use the Phillips screwdriver to remove the 4 screws from

hinge holder.

2. Open the printer top cover by pulling the top cover open lever located on each side

towards the front of the printer, then lift the top cover to the maximum open angle.

3. Use the Phillips screwdriver to remove the 6 screws from the top inner cover.

4. Use the slotted screwdriver to remove the 2 screws that hold the print head bracket.

Screws

Screws

Screws

Screws

Top cover

«
...
11
12
13
14
15
...
»

Содержание TTP-244CE series


































Отзывы:

Нет отзывов

Похожие инструкции для TTP-244CE series

Бренд: Magtek Страницы: 55

Бренд: Moneris Страницы: 25

Language Master LM-1

Бренд: Eiki Страницы: 16

Бренд: Prestigio Страницы: 6

Бренд: bq Страницы: 44

Бренд: Speedata Страницы: 8

PowerScan PD8590-DPM

Бренд: Datalogic Страницы: 128

Invexs 170 Series

Бренд: Nedap Страницы: 4

9200C - Digital Sender

Бренд: HP Страницы: 254

Бренд: HP Страницы: 13

Бренд: HP Страницы: 5

Бренд: HP Страницы: 4

Бренд: HP Страницы: 13

Wireless Barcode Scanner

Бренд: HP Страницы: 41

Linear Barcode Scanner II

Бренд: HP Страницы: 306

LaserJetsseries

Бренд: HP Страницы: 2

Sonitrol GS3-LF

Бренд: Stanley Страницы: 24

Бренд: Idea Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды