Tryton THG600, Руководство по эксплуатации

Страница: 5 / 48

5
other factors affecting the power tool work safety. If any
damage to the power tool is detected, it should be repaired
before use.
Improper power tool maintenance is a reason for many
accidents.
f) Cutting tools should be sharp and clean. Keeping sharp cutting
edges in good condition reduces the risk of jamming and facilitates
operation.
g) Power tools, equipment, working tools etc. should be used
according to this user's manual taking into account operating
conditions and the work to be done.
Misusing a power tool can
result in dangerous situations.
h) At low temperatures and after a long brakes in operation it is
recommended to turn the power tool to operate it with no
load for a few minutes to provide proper grease distribution
inside its driving mechanism.
i) Use soft, damp (cannot be wet) cloth and soap to clean power
tools. Do not use petrol, solvents and other agents that may
damage your equipment
.
j) Power tools can be stored/carried after making sure that all
moving components are locked and protected against
release with original devices intended for this purpose.
k) Store power tools in a dry, dust and water-protected place.
l) Carry your power tool in its original packaging to provide
protection against mechanical damage.
m) Keep handles and grip surfaces clean and free from oil and
grease. Secure grip and control over the tool in unexpected
circumstances are impossible if handles and grip surfaces are slippery.
WARNING! General warnings regarding the use of
power tools.
Repair :
WARNING! r
Personal S afety :
a) Prior to putting the electric tool aside wait until the cutting
shaft is fully stopped.
Naked blades may catch on the surface,
which may lead to uncontrolled movements of the toll and result in
heavy injuries.
b ) Never put hands into the chip ejector. Rotating parts present a
risk of injuries.
c ) Start the electric tool running idle, i.e. prior to applying the
blades to the material.
Otherwise there is a risk of jerks as the tool
may be seized in the machined part.
d ) While working with the plane hold the machine flat so that
the sole plates fully rest on the machined material.
Otherwise
the plane can be tilted while immersing into the material and cause
personnel injuries.
e) Never work with materials that may contain metal parts,
such as nails or screws.
It may damage the cutting shaft and the
cutter itself or lead to excessive vibrations.
f) Protect the object machined. Make sure all clamps are closed and
check for excessive clearance. It is safer to fix the object machined in a
fixing device or a vice than holding it in your hand.
a)
Each application of the tool not in line with the intended use as specified
below is strictly forbidden and makes the warranty terms null and void.
The manufacturer shall not be held responsible for possible
consequential damage that may arise due to or in connection with such
application.
Any modifications of the tool by the user relieve the manufacturer from
responsibility for any damage and injuries to the user and the
surroundings.
The plane
r should be used, operated and repaired exclusively by persons
knowing its detailed characteristics and safety rules. Accident prevention
regulations and all basic occupational health and safety regulations
Warranty and post-warranty repairs of its power tools are
should be observed alt all times.
carried out by PROFIX Service, which guarantees the best
Defective electric tools can be handed over for repairs exclusively to
quality or repair and use of genuine spare parts.
service workshops appointed by the tool manufacturer. The tools
supplied from electric grid shall be repaired exclusively by authorized
electricians.
Application of the tool in accordance with the intended use also refers to
its maintenance, storage, transportation and repairs.
g ) Do not use a power tool with its power cord damaged. Do not
touch the power cord when damaged; in case of damaging
the power cord during operation unplug it from the mains.
Damaged power cords increase the risk of electric shock.
ATTENTION! If a permanently fixed power cord becomes damaged, it must
be replaced with a special cable or assembly available at the manufacturer's
or at a specialized repair service point.
DESIGN AND APPLICATION AREA OF THE ELECTRIC PLANE R:
The electric planer is an electric tool that is designed for manual planning
and edge bevelling of wood and timber-derived materials.
The tool is a
device of the second class of electric protection (double insulation) and is
driven with use of a single-phase motor.
It is strictly forbidden to use the plane for any other application.
The plane r can never be used as a fixed tool.
The plane r is designed only for household (DIY) application. Do
never use the tool for applications that need use of professional
equipment.
The warranty terms are null and void when the tool is used at
craftsman workshops, for industrial applications or in similar
fields.
Electric plane , safety warnings –
Even in case of applications according to the intended use it is impossible
to completely eliminate certain factors of residual risk. Due to the
machine design and its structure the following hazards are present:
- I njuries due to rotating and moving parts;
- T hrowing a machined part or pieces of a machined part ;
- D amage of hearing when appropriate hearing protectors are not used ;
- E mission of timber dust hazardous for human health when works are
carried out in closed rooms (confined areas) ;
- D angerous to health when using the power tool for extended periods.
In such situations take regular breaks at work;
- Minor injuries while replacing components, blades and accessories.
n
Delivery kit :
ź
Electric plane r - 1 pc.
ź
G uide bar for parallel planing - 1 pc.
ź
Angle bracket to fix the guide bar- 1 pc.
ź
Fixing bolt of the angle bracket- 1 pc.
ź
Bolt to fix the guide bar to the angle bracket- 1 pc.