manualshive.com logo in svg

TruSteel AV30, Предустановка

Поделиться
Скачать
TruSteel AV30 Скачать руководство пользователя страница 16

AV30 PRE-INSTALLATION REQUIREMENTS | AV30 Pre-Installati on Requirements | v. 3.0

16 / 37

MODEL TaeEvoTECH
Air Cooled Chillers

The TAEevo range of air-cooled chillers are a packaged unit
designed for industrial applications. They are supplied with
hermetic scroll or reciprocating compressors and an
innovative finned pack evaporation inside the storage tank.

Technical Documents

Note: The installation instructions should be in the upper cabinet of the unit.

·

Installation Instructions (PDF) [2 MB]

·

Alarm Resets and Other Important Info (PDF) [5 MB]

SEE CHILLER REQUIREMENTS

Important Information

1. The chiller should be placed OUTSIDE of the facility, either on a roof, or a concrete

slab.  If placed inside, proper HVAC ventilation is required.  The
chiller CANNOT operate in a closed space; the unit dissipates a lot of heat.  Please
contact MTA (Manufacturer) if you have any doubt of chiller placement.

2. The bypass manifold, provided by TruSteel, should be properly installed by a

plumber.  Use plumbers dope AND plumbers tape.

3. The copper plumbing(Crimped or Push Connect – NO FLUX) will be run to the shark

bite side of the ball valves provided. The ball valves are mounted on a unistrut.

4. The chiller requires a 

propylene glycol/water mixture

. Please refer to the

Installation Instructions to verify how much propolyene glycol your unit will require.
(Ratio is climate dependant) 

Link to Purchase

5. Please note that the chiller IS NOT powered by the AutoVap30 Control Panel.  The

chiller is not controlled by the AutoVap30.  The AutoVap30 only monitors, not

Содержание AV30






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды