background image

2

SAFETY

SPARK ARRESTOR NOTE 

NOTE: For users on U.S. Forest Land and in the states of 

California, Maine, Oregon and Washington. All U.S. Forest Land 

and the state of California (Public Resources Codes 4442 and 

4443), Oregon and Washington require, by law that certain internal 

combustion engines operated on forest brush and/or grass-covered 

areas be equipped with a spark arrestor, maintained in effective 

working order, or the engine be constructed, equipped and 

maintained for the prevention of fire. Check with your state or local 

authorities for regulations pertaining to these requirements. Failure 

to follow these requirements could subject you to liability or a fine. 

This unit is factory equipped with a spark arrestor. If it requires 

replacement, contact your local service dealer to install the 

appropriate muffler assembly.

Read the operator’s manual and follow all warnings and safety 

instructions. Failure to do so can result in serious injury to the 

operator and/or bystanders.

 SYMBOL

MEANING

WARNING:

 Signals a SERIOUS hazard. 

Failure to obey a safety WARNING symbol CAN result in 

serious injury to yourself or to others.

CAUTION:

 Signals a MODERATE hazard.  

Failure to obey a safety CAUTION symbol MAY result in 

property damage or injury to yourself or to others.

The purpose of safety symbols is to attract your attention to 

possible dangers. The safety symbols, and their explanations, 

deserve your careful attention and understanding. The safety 

warnings do not by themselves eliminate any danger. The 

instructions or warnings they give are not substitutes for proper 

accident prevention measures.

NOTE: Advises you of information or instructions vital to the 

operation or maintenance of the equipment.

DANGER:

 Signals an EXTREME hazard. 

Failure to obey a safety DANGER symbol WILL result in 

serious injury or death to yourself or to others.

WARNING:

 This product can expose you to 

chemicals including engine exhaust, which is known to the 

State of California to cause cancer, and carbon monoxide, 

which is known to the State of California to cause birth 

defects or other reproductive harm. For more information 

go to www.P65Warnings.ca.gov.

TABLE OF CONTENTS 

Service  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 

Safety  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 

Know Your Unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 

Essential Terms and Definitions  . . . . . . . . . . . . . . . . . . . . . . . . . . .8 

Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 

Oil and Fuel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 

Starting and Stopping  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 

Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 

Cleaning and Storage  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 

Warranty  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

All information, illustrations, and specifications in this manual are based 

on the latest product information available at the time of printing. We 

reserve the right to make changes at any time without notice. 

The product may vary slightly from the illustrations contained in this 

manual. 

Copyright© 2021 MTD SOUTHWEST INC, All Rights Reserved.

NOTE: This operator's manual covers multiple models. Features 

may vary by model. Not all features in this manual are applicable 

to all models. The model depicted may differ from yours.

SERVICE

DO NOT RETURN THIS UNIT TO THE RETAILER. PROOF OF 

PURCHASE WILL BE REQUIRED FOR WARRANTY 

SERVICE. 

For assistance regarding the assembly, operation or maintenance of 

the unit, please call 1-800-828-5500 (in the United States) or 1-800-

668-1238 (in Canada). Additional information can be found at 

www.troybilt.com (in the United States) or www.troybilt.ca (in 

Canada). 

Warranty service is available through an authorized service center. 

To locate a service center in your area, please visit our website or 

call the number listed above. Service on this unit, both within and 

after the warranty period, should only be performed by an authorized 

and approved service center. When servicing, use only identical 

replacement parts.

Register your product at www.troybilt.com (US) or www.troybilt.ca

(Canada) to have parts, owner manuals, and warranty information at 

your fingertips.

Содержание TB4216H XP

































































Отзывы: