INSTALLING AND ADJUSTING THE WHEEL ASSEMBLY
Installing the Wheel Assembly
1. Insert the wheel assembly into the wheel bracket. The "J"
shape of the wheel assembly should point away from the unit
(Fig. 1).
2. Align the hole in the wheel bracket with the desired hole in the
wheel assembly (Fig. 1).
3. Insert the clevis pin through the aligned holes (Fig. 1).
4. Insert the cotter pin into the clevis pin (Fig. 1).
NOTE:
It may be necessary to adjust the position of the wheel
assembly before using the unit.
Adjusting the Wheel Assembly
1. Remove the cotter pin from the clevis pin (Fig. 1).
2. Remove the clevis pin from the wheel bracket and wheel assembly (Fig. 1).
3. Align the hole in the wheel bracket with the desired hole in the wheel assembly (Fig. 1).
NOTE:
Moving the wheel assembly down will raise the wheel height. Moving the wheel assembly up
will lower the wheel height.
4. Insert the clevis pin through the aligned holes (Fig. 1).
5. Insert the cotter pin into the clevis pin (Fig. 1).
POSITIONING THE HANDLEBARS
1. Loosen the two knobs on the inside of the handlebars (Fig. 2).
2. With the unit upright, swing the handlebars up into the
operating position (Fig. 3).
NOTE:
Take care not to pinch the throttle cable or switch wires
when positioning the handlebar.
3. Tighten the knobs to secure the handlebars in place.
NOTE:
Do not over-tighten the knobs.
3
APPLICATIONS
• Cultivating sod and light to medium soil
• Cultivating in garden areas, around trees, etc.
• Edging
KNOW YOUR UNIT
ASSEMBLY
Tine Guard
Fuel Cap
Handlebar
Handlebar Knobs
Starter Rope
Grip
Throttle Control
Air Filter Cover
Muffler
On/Off Control
Primer Bulb
Cultivator Tines
Oil Fill Plug
Spark Plug
Wheel Support
Bracket
OIL AND FUEL
USING THE RIGHT OIL
Use a high-quality SAE 30 weight oil of API (American Petroleum Institute) service class SJ.
DO NOT
use dirty oil. Failure to use clean oil of the correct type can cause premature engine wear and failure.
ADDING OIL: INITIAL USE
NOTE:
This unit was shipped without oil in the crankcase. Oil must
be added before starting the unit.
NOTE:
This unit comes with a 3.04 fluid oz. (90 ml) bottle of oil.
1. Unscrew the top of the oil bottle. Remove the paper seal.
Reinstall the top of the oil bottle.
2. Remove the cap from the oil bottle. Cut the tip off the funnel
spout (Fig. 4).
3.
Set the unit on a flat, level surface.
4. Unscrew the oil fill plug (Fig. 5).
5. Pour the entire bottle into the oil fill hole (Fig. 5).
DO NOT
overfill. Refer to
Checking the Oil Level
.
NOTE:
Never add oil directly to the fuel tank. This unit has a four-
cycle engine.
DO NOT
mix oil with gasoline.
6. Wipe up any oil that may have spilled.
7. Reinstall the oil fill plug.
NOTE:
Make sure the O-ring is in place on the oil fill plug (Fig. 5).
NOTE:
Save the empty oil bottle. Use the bottle to measure the
correct amount of oil during future oil changes.
WARNING:
OVERFILLING THE CRANKCASE MAY CAUSE SERIOUS PERSONAL
INJURY. Check the oil level before each use. The importance of maintaining the proper oil
level cannot be overemphasized. Change the oil according to the
Maintenance Schedule
.
USING THE RIGHT FUEL
The use of old fuel is the most common cause of performance problems. Use only fresh, clean
unleaded gasoline.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and oxygenates such as ethanol, methanol or MTBE
(ether). Alcohol-blended fuel absorbs water. As little as 1% water in the fuel can make fuel and oil
separate, forming acids when stored. ALWAYS use fresh fuel (less than 30 days old).
NOTE:
Dispose of old fuel according to federal, state and local regulations.
Using Blended Fuels
If using a blended fuel:
•
Always use fresh unleaded gasoline
•
Use the fuel additive STA-BIL® or an equivalent
•
Drain the tank and run the engine dry before storing the unit
Using Fuel Additives
Use a fuel additive, such as STA-BIL Fuel Stabilizer or an equivalent, to inhibit corrosion and minimize
gum deposits. Add 0.8 oz. (23 ml) of fuel additive per gallon of fuel, according to the instructions on
the container. NEVER add fuel additives directly to the unit's fuel tank.
FUELING THE UNIT
1. Position the unit with the fuel cap facing up.
2. Remove the fuel cap.
3. Place the fuel container spout into the fill hole on the fuel tank and fill the tank.
NOTE:
Do not overfill the tank.
4. Wipe up any fuel that may have spilled.
5. Reinstall the fuel cap.
6. Move the unit at least 30 ft. (9.1 m) from the fuel container and the fueling site before starting the
engine.
WARNING:
DO NOT USE E85 FUEL IN THIS UNIT.
It has been proven that fuel
containing greater than 10% ethanol will likely damage this engine and void the warranty.
WARNING:
Gasoline is extremely flammable. Ignited vapors may explode. Always stop
the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the
tank. Keep sparks and open flames at a distance from the area.
WARNING:
Remove the fuel cap slowly to avoid injury from fuel spray. Never operate the
unit without the fuel cap securely in place.
WARNING:
Add fuel in a clean, well ventilated outdoor area. Wipe up any spilled fuel
immediately. Avoid creating a source of ignition for spilled fuel. Do not start the engine until
fuel vapors dissipate.
Fig. 4
Fig. 5
Funnel
Spout
Oil Fill Plug
O-Ring
Oil Fill
Hole
NO ASSEMBLY TOOLS REQUIRED
Fig. 2
Handlebar Knobs
Fig. 3
Fig. 1
Wheel
Assembly
Clevis Pin
Cotter Pin
Wheel Bracket
WARNING:
To prevent serious personal injury, the wheel assembly must be installed
when operating the unit.
WARNING:
To avoid injury from the tines, wear heavy gloves and a long sleeve shirt
when installing the wheel assembly.
