Troy-Bilt 21A-630B063 Скачать руководство пользователя страница 40

Страница: 40 / 42

Troy-Bilt Small Frame Tillers

3.3.

Remove the reverse clutch cable’s Z-fitting from
the reverse idler arm. See Figure 3.3.

NOTE:

The reverse return spring will drop off its

anchoring position at the left frame rail. Make
certain it is correctly installed during assembly.
See the Image Below.

3.4.

Loosen the lock nut securing the reverse idler
pulley belt guide in position using a 1/2” socket
and wrench. See Figure 3.4.

3.5.

Remove the reverse drive belt from the reverse
idler pulley.

3.6.

Remove all four self-tapping screws securing the
pulley/belt guard to the left and right engine
brackets using a 3/8” socket and wrench.

NOTE:

The wheel and tire assemblies can be

move outward for extra clearance.

3.7.

Remove the pulley/belt guard.

Figure 3.3

Reverse

Clutch Cable

Reverse Idler Arm

Z-Fitting

Reverse Return Spring Location

Reverse

Return Spring

Anchor

Position

Figure 3.4

Lock Nut

Belt Guide

Reverse Drive

Belt

Figure 3.6

Self-Tapping Screws

Содержание 21A-630B063











































Результаты поиска

Содержание 21A-630B063

Отзывы:

Похожие инструкции для 21A-630B063

Бренды по названию

Популярные бренды

Troy-Bilt 21A-630B063, Руководство по обслуживанию

Результаты поиска

Содержание 21A-630B063

Отзывы:

Похожие инструкции для 21A-630B063

Бренды по названию

Популярные бренды