Troy-Bilt 21A-630B063 Скачать руководство пользователя страница 11

Страница: 11 / 42

Troy-Bilt Small Frame Tillers

TRANSMISSION REMOVAL:

NOTE:

Perform the Drive Belt Replacement sec-

tion through forward drive belt removal, prior to
performing this section. See Image Below

6.1.

Loosen the hex nut securing the forward clutch
cable to the lower cable mounting bracket using
a 3/8” wrench and a 7/16” wrench.

6.2.

Slide the forward clutch cable out of the lower
cable mounting bracket.

6.3.

Pivot the forward clutch cable’s Z fitting rear-
ward, and remove it from the forward idler lever.

6.4.

Remove the lower portion of the forward clutch
cable from the belt cover.

6.5.

Set the belt cover aside.

6.6.

Remove both self tapping hex flange screws
securing the tine hood to the right and left hood
brackets using a 3/8” socket. See Figure 6.6.

Remove Drive Belt

Remove

Drive Belt

Figure 6.6

Self Tapping

Hex Flange Screws

6.7.

Grasp the upper handlebar and pivot the unit
onto it’s nose.

6.8.

Secure the handlebar from above.

6.9.

Pivot the trailing shield up.

6.10. Remove the hex screw, bushing, lock washer

and lock nut securing the drag bar to the bottom
of the transmission using a 1/2” socket and
wrench. See Figure 6.10.

6.11. Remove both hex flange screws securing the

hood brackets to the transmission assembly
using a 1/2” socket. See Figure 6.11.

Figure 6.10

Hex Screw

Lock Nut

Lock Washer

Figure 6.11

Hex Flange Screws

Hood

Brackets

Содержание 21A-630B063











































Результаты поиска

Содержание 21A-630B063

Отзывы:

Похожие инструкции для 21A-630B063

Бренды по названию

Популярные бренды

Troy-Bilt 21A-630B063, Руководство по обслуживанию

Результаты поиска

Содержание 21A-630B063

Отзывы:

Похожие инструкции для 21A-630B063

Бренды по названию

Популярные бренды