background image

If the platform position is too low to be install, or the platform 
position is too high

distance

3mm)

Then the leveling module 

needs to be adjusted to make the platform zero position closer to 
the printing area

≈1mm)

, First remove the platform, adjust the 

leveling jackscrew as shown in the picture

6)

Clockwise raises up, 

counterclockwise to lower. Test every 10 

°

rotation, by returning to 

zero, After zeroing, install the platform and observe whether the 
height is appropriate. Repeat this step for several times until the 
platform position is about 1mm higher than the printing area

The 

platform must be removed before repeated operation)

Then 

according to the

①②③

step leveling.

FIG

6

Try printing: click            and select "test file", then click            Start 
printing.

After leveling, raise the platform to the middle height, push the 
resin vat into the printing area flat, tighten two thumb screws (the 
screws are placed in the groove of the resin vat), and pour the resin 
to the height of about 1/3 to 1/2 of the resin vat (

to prevent 

overflow, it is easy to exceed 1/2 height

).

9

Содержание Ultrabot

















Отзывы: