background image

 

User Manual Qiwi Lite 
Support: www.tronteq.de/support 
Release 11/2016 

 

Seite 26 von 31

 

9. 

Configuration with USB flash drive 

9.1. 

Function  

The used USB flash drive must only have one partition and must be in the FAT format. The following 
formats are supported: FAT12, FAT16, and FAT32.  
 
New  data  of  a  USB  flash  drive  is  automatically  applied  only  if  the  flash  drive  is  authenticated  with  a 
valid  user  name  and  password.  Therefore  a  authentication  file  named 

„userpassword.pass“ must be 

on the USB flash drive.  
 

 

To perform the configuration via USB flash drive a valid authentication file 
must be on the USB flash drive.  

 
The authentication file must be an ASCII-coded test file without formatting. In the first line must contain 
the user name, the second the password. 
 
The structure of the directory of the USB flash drive must look like that:  
 

USB flash drive - directory 

►  userpassword.pass 
►  log 

►  logfile1.log  
►  logfile2. log 
►  … 

►  configuser 

► 

config.

cfg 

►  confignew.cfg 

►  newpassword.pass 
►  OSYS_TQPRODUCT_Rxx.bin 

 

9.2. 

Perform the configuration  

To change the configuration of the switch, a valid configuration file in the folder "configuser" of the 
USB flash drive must be present. The configuration file must be "confignew.cfg". After 
plugging the USB flash drive into the switch, the device will load automatically the new configuration 
file and apply it after the successful authentication. 
 

 

Содержание Qiwi Lite
































Отзывы: