22
10318
ASSEMBLY STEPS
STEP 11:
•
Thread the Low Cable (64) through brackets as shown on the next page.
•
With the Low Cable (64) in the groove of Red Pulley (53), install Pulley (H) into the Leg Extension (11)
using one Hex Bolt 3/8” x 2-1/2” (72), two Bushings Ø13 X T1.0 X 11 mm (98), two Washers 3/8” (90)
and one Lock Nut 3/8” (85).
•
With the Low Cable (64) in the groove of the Pulley (54), install Pulley (I) with two Pulley Guards (101)
into the Seat Support Post (10) using one Hex Bolt 3/8” x 3” (79), two Bushings Ø13 X T1.0 X 17 mm
(99), two Washers 3/8” (90) and one Lock Nut 3/8” (85).
•
With the Low Cable (64) in the groove of Pulley (54), install Pulleys (J,L) with four Pulley Brackets (104)
into the brackets of the Bench Press Arm (13) using one Hex Bolt 3/8” x 3-3/8” (70), two Washers 3/8”
(90) and one Lock Nut 3/8” (85).
•
With the Low Cable (64) in the groove of Pulley (54), install the Pulley (K) with two Pulley Guards (101)
into the slot of the Vertical Post (3) using one Hex Bolt 3/8” x 3-3/8” (70), two Washers 3/8” (90), two
Bushings Ø13 X T1.0 X 22 mm (100) and one Lock Nut 3/8” (85).
•
With the Low Cable (64) in the groove of Pulley (54), install the Pulley (M) with two Pulley Brackets
(104) into the bracket of the Vertical Post (3) using one Hex Bolt 3/8” x 2” (74), two Washers 3/8” (90)
and one Lock Nut 3/8” (85).
•
With the Low Cable (64) in the groove of Pulley (54), install the Pulley (N) with two Pulley Brackets
(104) into the lower Intersect Pulley Bracket (25) using one Hex Bolt 3/8” x 2” (74), two Washers 3/8”
(90) and one Lock Nut 3/8” (85).
•
With the Low Cable (64) in the groove of Pulley (54), install the Pulley (O) with two Pulley Brackets
(104) into the bracket of Main Base (1) with one Hex Bolt 3/8” x 2” (74), two Washers 3/8” (90) and
one Lock Nut 3/8” (85).
•
With the Low Cable (64) in the groove of Pulley (54), install the Pulley (P) with two Pulley Brackets
(104) into the lower Pulley Bracket Piece (24) using one Hex Bolt 3/8” x 2” (74), two Washers 3/8” (90)
and one Lock Nut 3/8” (85).
•
With the Low Cable (64) in the groove of Pulley (54), install the Pulley (Q) with two Pulley Brackets
(104) into the bracket of Main Base (1) using one Hex Bolt 3/8” x 2” (74), two Washers 3/8” (90) and
one Lock Nut 3/8” (85).
•
With the Low Cable (64) in the groove of Pulley (54), install the Pulley (R) into the bracket of Leg Frame
(106) using one Hex Bolt 3/8” x 2” (74) and one Washer 3/8” (90).
•
With the Low Cable (64) in the groove of Pulley (54), install the Pulley (S) with two Pulley Guards (101)
into the Leg Frame (106) using one Hex Bolt 3/8” x 3-3/4” (78), two Bushings Ø13 X T1.0 X 26 mm
(125), two Washers 3/8” (90) and one Lock Nut 3/8” (85).
Содержание RECUMBENT 400
Страница 13: ...13 10318 EXPLODED DRAWING ...
