background image

Triton Showers

Triton Road

Nuneaton

Warwickshire  CV11 4NR

Triton is a division of Norcros Group (Holdings) Limited

TriTon STandard GuaranTee

Triton guarantee this product against all 

mechanical and electrical defects arising from faulty 

workmanship or materials for a period of one year 

for domestic use only, from the date of purchase, 

provided that it has been installed by a competent 

person in full accordance with the 
fitting instructions.
Any part found to be defective during this 

guarantee period we undertake to repair or replace 

at our option without charge so long as it has been 

properly maintained and operated in accordance 

with the operating instructions, and has not been 

subject to misuse or damage.
This product must not be taken apart, modified or 

repaired except by a person authorised by Triton. 

This guarantee applies only to products installed 

within the United Kingdom and does not apply to 

products used commercially. This guarantee does 

not affect your statutory rights.

What is not covered:

1

Breakdown due to: 

a)

 use other than domestic 

use by you or your resident family; 

b)

 wilful act or neglect; 

c)

 any malfunction 

resulting from the incorrect use or quality of 

electricity, gas or water or incorrect setting of 

controls;

d)

 faulty installation.

2

Repair costs for damage caused by foreign 

objects or substances.

3

Total loss of the product due to non-availability 

of parts.

4

Compensation for loss of use of the product or 

consequential loss of any kind.

5

Call out charges where no fault has been found 

with the appliance.

6

The cost of repair or replacement of pressure relief 

devices, showerheads, hoses, riser rails and/or wall 

brackets, isolating switches, electrical cable, fuses 

and/or circuit breakers or any other accessories 

installed at the same time.

7

The cost of routine maintenance, adjustments, 

overhaul modifications or loss or damage arising 

therefrom, including the cost of repairing 

damage, breakdown, malfunction caused by 

corrosion, furring, pipe scaling, limescale, system 

debris or frost.

Customer Service: 

0844 980 0750

Trade installer Hotline: 

0844 980 0730

Fax:

 

0844 980 0744

www.tritonshowers.co.uk 

e-mail: [email protected]

TRITON reserve the right to change product specification without prior notice. E&OA. © TRITON SHOWERS 2009

Service Policy

In the event of a product fault or complaint occurring, the 

following procedure should be followed:

1

Telephone Customer Service on 0844 980 0750 having available, 

your details including post code, the model number and power 

rating of the product, together with the date of purchase.

2

Based on information given over the telephone, a Triton Customer 

Service Advisor will attempt to diagnose the fault and confirm 

whether a site visit from a qualified service engineer is required.

3

All products attended to by a Triton service engineer must be 

installed in full accordance with the Triton installation guide 

applicable to the product. (Every product pack contains an 

installation guide, however, they can also be bought via our 

Customer Service Spares Department).

4

Our engineer will require local parking and if a permit is required 

this must be available to the engineer on arrival at the call. 

5

It is essential that you or an appointed representative (who must 

be over 18 years of age) is present for the duration of the service 

engineer's visit. If the product is in guarantee you must produce 

proof of purchase.

6

Where a call under the terms of guarantee has been booked 

and the failure is not product related (i.e. scaling and furring, 

incorrect water pressure, pressure relief device operation or 

electrical/plumbing installation fault) a charge will be made. A 

charge will also be issued if nobody is at home when the service 

engineer calls or adequate parking/permit is not available.

7

If the product is no longer covered by the guarantee an up front 

fixed fee will be charged before the site visit.

8

Should proof of purchase not be available on an “in-guarantee” 

call, or should the service engineer find that the product is no 

longer under guarantee, the engineer will charge the same 

fixed price and the customer will be expected to pay the 

engineer before he leaves. If payment is not made on the day an 

administration charge will be added to the fixed charge.

9

If a debt is outstanding from a previous visit, or from any other 

Triton purchase, Triton reserves the right to withhold service until 

the debt has been settled.

10

Triton takes the health, safety and wellbeing of its employees very 

seriously and expects customers to treat all staff members with 

respect. Should any employee feel threatened or receive abuse, 

either verbally or physically, Triton reserves the right to withhold 

service and will support the employee with a legal prosecution.

replacement Parts Policy

Availability: It is the policy of the manufacturer to maintain parts 

availability for the duration of production and a period of five years 

thereafter, in accordance with industry standards.

Spare parts are available via our website, 

www.tritonshowers.co.uk

,

or by telephoning Triton Customer Service Spares Department.  

Payment should be made by credit/debit card (excluding American 

Express or Diners Card).

Payment can also be made by pre-payment of a pro forma invoice by cheque or money order.

Extended Warranty AVAILABLE NOW. Call 0844 980 0740 for more details.

Содержание T90xr






























Отзывы: