Triton SFX8008GSI Скачать руководство пользователя

Страница: 23 / 28

Instructions for installers and service engineers only

INSTRUCTIONS FOR INSTALLERS AND SERVICE ENGINEERS ONLY

Instructions for installers and service engineers only

CLEANING THE FILTER

It is recommended that the filter is periodically
cleaned in order to maintain the performance of
the shower. It is essential that this operation is
carried out by a competent person.

IMPORTANT:

Before servicing, switch off the

electricity supply at the mains.

• Switch off the water supply at the lsolator

valve.

• The inlet filter is situated inside the water inlet

fitting

(fig.21)

• To gain access to the filter, remove the cover.
• Unscrew the filter cap from the bottom of the

inlet pipe.

• Inspect the ‘O’ ring for damage when the

filter cap is removed.

• When cleaning the filter,

DO NOT

use a sharp

object as it will cause damage. It is preferable
to use an old toothbrush or similar.

• To reassemble, follow the procedure in

reverse.

• Make sure that the sealing ‘O’ ring is in place.
•

DO NOT

over tighten the filter cap on

reassembly.

NOTE:

Full commissioning procedure will need

to be performed after cleaning of the filter - see

page 20

for information on commissioning

procedure.

Fig.21

Filter

assembly

‘O’ ring

Inlet

Содержание SFX8008GSI





























Результаты поиска

Содержание SFX8008GSI

Отзывы:

Похожие инструкции для SFX8008GSI

Бренды по названию

Популярные бренды

Triton SFX8008GSI, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SFX8008GSI

Отзывы:

Похожие инструкции для SFX8008GSI

Бренды по названию

Популярные бренды