Triton NOVA Thermostatic Series Скачать руководство пользователя страница 24

Страница: 24 / 28

Electric shower

FAULT FINDING/TROUBLESHOOTING

Problem

Cause

Action

Shower varies from
normal temperature to
cold during use.

5.1

Water pressure has

dropped below
minimum required.

5.1.1

Wait until the water pressure resumes to

normal.

Pressure relief device has

operated

(water ejected

from PRD tube)

6.1

Blocked shower head.

6.1.1

Clean or replace blocked sprayplate in

shower head and then fit new PRD.

6.2

Twisted/blocked

flexible shower hose.

6.2.1

Check for free passage through hose.

Replace the hose if necessary and fit new
PRD.

6.3

Shower head not

removed while
commissioning.

6.3.1

Fit new PRD. Commission unit with shower

head removed.

6.4

Water pressure above

specified maximum for
unit

(see rating label).

6.4.1

Fit pressure reducing valve to inlet and then

fit new PRD.

Shower fails to shut off

flow when Start/Stop
button is pressed.

7.1

Faulty Start/Stop

switch.

7.1.1

Replace switch.

7.2

Debris in solenoid

valve.

7.2.1

Replace solenoid valve.

7.3

Unit malfunction.

7.3.1

Have unit checked. Contact Customer

Experience.

FAULT FINDING

Important:

Switch off the electricity at the mains supply and remove the circuit fuse before

attempting any fault finding inside the unit.

Problem/Symptom Cause

Action/Cure

NOTE:

Identify cause of operation before fitting new PRD unit.

When fitting a new PRD, follow the commissioning procedure.

It is advised all electrical maintenance/repairs to the shower

should be carried out by a suitably qualified person.

In the unlikely event of a fault occurring please contact Triton Customer Service.

DO NOT remove the shower from the installation.

Содержание NOVA Thermostatic Series





























Результаты поиска

Содержание NOVA Thermostatic Series

Отзывы:

Похожие инструкции для NOVA Thermostatic Series

Бренды по названию

Популярные бренды

Triton NOVA Thermostatic Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NOVA Thermostatic Series

Отзывы:

Похожие инструкции для NOVA Thermostatic Series

Бренды по названию

Популярные бренды