background image

Triton Showers 

Triton Road 

Nuneaton 

Warwickshire  CV11 4NR

Triton is a division of Norcros Group (Holdings) Limited

TRITON reserve the right to change product specification without prior notice. E&OA. © TRITON SHOWERS 2008

Service Policy

In the event of a complaint occurring, the following 

procedure should be followed:

1

  Telephone Customer Service on  

0870 067 3333

 

(0845 762 6591 in Scotland and 

in Northern Ireland)

, having available the model 

number and power rating of the product, together 

with the date of purchase.

2

  Triton Customer Service will be able to confirm 

whether the fault can be rectified by either the 

provision of a replacement part or a site visit 

from a qualified Triton service engineer.

 

If a service call is required the unit must be fully 

installed for the call to be booked and the date 

confirmed. In order to speed up your request, 

please have your postcode available when 

booking a service call.

4

  It is essential that you or an appointed  

representative (who must be a person of 18 years 

of age or more) is present during the service 

engineer's visit and receipt of purchase is shown.

5

 

A charge will be made in the event of an aborted 

service call by you but not by us, or where a call 

under the terms of guarantee has been booked 

and the failure is not product related (i.e. scaling 

and furring, incorrect water pressure). 

6

  If the product is no longer covered by the 

guarantee, a charge will be made for the site 

visit and for any parts supplied.

7

  Service charges are based on the account being 

settled when work is complete, the engineer 

will then request payment for the invoice. If this 

is not made to the service engineer or settled 

within ten working days, an administration 

charge will be added.

Replacement Parts Policy

Availability:

 It is the policy of Triton to maintain 

availability of parts for the current range of 

products for supply after the guarantee has 

expired. Stocks of spare parts will be maintained 

for the duration of the product’s manufacture and 

for a period of five years thereafter.

  In the event of a spare part not being available a 

substitute part will be supplied.

Payment: 

The following payment methods can be 

used to obtain spare parts:

1

   By post, pre-payment of pro forma invoice by 

cheque or money order.

2

   By telephone, quoting credit card (MasterCard 

or Visa) details.

3

   By website order, www.tritonshowers.co.uk

TRiTon STandaRd GuaRanTee

Triton guarantee this product against all mechanical 

defects arising from faulty workmanship or materials 

for a period of three years for domestic use only, 

from the date of purchase, provided that it has been 

installed by a competent person in full accordance 

with the fitting instructions.
Any part found to be defective during this 

guarantee period we undertake to repair or replace 

at our option without charge so long as it has been 

properly maintained and operated in accordance 

with the operating instructions, and has not been 

subject to misuse or damage.
This product must not be taken apart, modified or 

repaired except by a person authorised by Triton. 

This guarantee applies only to products installed 

within the United Kingdom and does not apply to 

products used commercially. This guarantee does 

not affect your statutory rights.

What is not covered:

1

 

Breakdown due to: 

a)

 use other than domestic 

use by you or your resident family;  

b)

 wilful act or neglect; 

c)

 any malfunction 

resulting from the incorrect use or quality of 

water or incorrect setting of controls; 

d)

 faulty 

installation.

2

 

Repair costs for damage caused by foreign 

objects or substances.

3

  Total loss of the product due to non-availability 

of parts.

4

  Compensation for loss of use of the product or 

consequential loss of any kind.

5

 

Call out charges where no fault has been found 

with the appliance.

The cost of repair or replacement of 

showerheads, hoses, riser rails and/or wall 

brackets or any other accessories installed at the 

same time.

The cost of routine maintenance, adjustments, 

overhaul modifications or loss or damage arising 

therefrom, including the cost of repairing 

damage, breakdown, malfunction caused by 

corrosion, furring, pipe scaling, limescale, system 

debris or frost.

Customer Service: 

0870 067 3333

Scottish and northern ireland 

Customer Service: 

0845 762 6591

 Trade installer Hotline: 

0870 067 3767 

Fax: 

 

0870 067 3334

www.tritonshowers.co.uk 

e mail: [email protected]

Содержание COMBI 2180206H





































Отзывы: