manualshive.com logo in svg

TRISTAN TECHNOLOGIES SMM-770, Руководство по эксплуатации

Поделиться
Скачать
TRISTAN TECHNOLOGIES SMM-770 Скачать руководство пользователя страница 36

Model SMM 770 Scanning Magnetic Microscope System 

TRISTAN TECHNOLOGIES --Page 

36

 

 

Figure 4-6: 

Manual control of the sample stage

 

CAUTION 

The user must ensure that the stage is clear of obstacles throughout the entire working 

region (154 mm x 154 mm) before homing starts. Improperly placed samples could cause 

permanent damage to the sample and/or dewar. The Tristan warranty does not cover 

resulting damage.

 

The 

HALT

 button will immediately terminate movement. The 

HOME

 button will force the 

stage to home; this is theoretically unnecessary, but this utility is provided in the event of a 
hardware error. 

4.5 SQUID PARAMETERS 

The 

SQUID

 tab controls the iMAG settings. Tristan strongly recommends making 

adjustments to the iMAG by using these controls rather than the physical front panel of the 
instrument. Changes made from the physical front panel may not be registered in the 
software, and thus the data displays and files would be inaccurate. This is of special 
concern with the gain setting. 
The data output of the iMAG can be viewed in the 

Raw Data

 tab. This is especially useful 

during a manual tune of the iMAG. 

Содержание SMM-770













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды