background image

Herrtronic

®

 Model 6000

I n s t a l l a t i o n ,   O p e r a t i o n ,   &   M a i n t e n a n c e   M a n u a l

8

www.trioniaq.com

Control Circuit Connections

WARNING!

Do  not  install  any  controls  inside  the  Herrtronic  6000 

cabinet.  Installations  of  any  extraneous  devices  inside 

the electrical compartment may cause erratic behavior of 

the circuitry and will VOID the warranty.

The 6000 units with built-in blowers require no external control 

wiring since the humidistat is built-in.

SECTION IV OPERATING INSTRUCTIONS

Start-up Instructions

1. 

Check that the humidifier is properly mounted and level.

2. 

Check that the water fill and drain are properly connected.

3.  Check that the correct voltage and amperage service are 

supplied.

4.  With power off, double check all electrical connections and 

plumbing connections to ensure that they did not loosen 

during shipment.

5.  With the “on-off-drain” switch in the “off” position, and the 

control humidistat at its lowest setting, turn on the main 

disconnect. The contactor should remain deenergized 

and the power light should remain “off”. Place the “on-off-

drain” switch in the “on” position and the power light should 

illuminate.

6.  Turn the control humidistat up to its highest setting. The 

contactor should pull in.

7. 

After approximately a 5 second delay, the fill valve energizes 

and water begins to fill the cylinder to the preset amp level 

or cylinder full condition, depending on the incoming water 

supply. When starting up the unit, it is best to put an amp 

clamp on the power leg that passes through the toroid 

transformer. Ensure that the humidifier fills to “cylinder full” 

(approximately 1.5” from the top of the cylinder), or that 

the amperage reaches the data plate maximum and the fill 

valve de-energizes.

NOTE:

If  upon  initial  start-up  of  this  humidifier  the  cylinder  is 

slow in heating and/or the service light continues to come 

on, drain the cylinder to 1/4 full. Turn off power at break

-

er, obtain some Alka-Seltzer tablets and crumble 1/2 of 

one tablet (Alka-Seltzer) into the grey fill tee. Change the 

middle blue dial on the left side of the circuit board, R18, 

from 90% to 87%. Then turn the breaker on and run the 

unit. If you have had to use these this step on a 240V unit 

(6000-2,4),  it  is  advisable  that  you  order  a  GT-176-1  re

-

placement cylinder rather than the standard replacement 

cylinder in the future so this procedure will not need to 

be repeated. Upon receipt of the GT-176-1 cylinder, adjust 

the dial, R18, on the circuit board back to 90%.

VIEW IN FROM RIGHTSIDE OF UNIT

TRANSFORMER

L1 L2

RELAY

TERMINAL BLOCK

  FILL VALVE

MOUNTING SCREWS

  FILL VALVE

ADJUSTING SCREW

CYLINDER FULL

  INTERFACE

8.  All units are equipped with a drain tempering feature which 

mixes  cold  fill  water  with  the  hot  drain  water  to  protect 

drain piping. Depending on your fill water pressure, some 

adjustment of the fill metering valve may be necessary to 

ensure drain water of less than 140°F. (See Figure 5.) To 

deactivate, remove diode from socket CRI8 from circuit 

board. (See Figure 7.)

9.  Reset control humidistat to its desired settings. Typical 

control humidistat settings are 30-40%.

NOTE:

The capacity of the humidifier can be adjusted between 

50%  and  100%  of  the  maximum  level  by  adjusting  the 

capacity adjustment potentiometer (labeled R39) on the 

main circuit board.  All units are set from the factory to 

produce 4 lbs/hr. If the psychrometric conditions permit, 

the  6000—2  may  be  increased  to  8  lbs/hr  by  adjusting 

R39 from 50%  to 100% capacity. Refer to Figure 7.

CAUTION!

Inadequate airflow may allow humidity to collect in areas 

causing condensation.

Figure 5

Содержание Herrmidifier Herrtronic 6000 Series



















Отзывы: