manualshive.com logo in svg

Trion AIR BOSS, Руководство пользователя, Страница: 2 / 16

Поделиться
Скачать
Trion AIR BOSS Скачать руководство пользователя страница 2

READ AND SAVE THESE INSTRUCTIONS”

WARNING!

TO REDUCE THE RISK OF FIRES, ELECTRICAL SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:

A.

 

Installation work and electrical wiring must be done by qualified person(s) in accordance
with all applicable codes and standards, including fire-rated construction.

B.

 

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hidden utilities.

C.

 

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the
application.

D.

 

Use this unit in the manner intended by the manufacturer.  If you have any questions,
contact the manufacturer.

Trion, Inc.
101 McNeill Road
Sanford, North Carolina  27330, U.S.A.
Tel:

(919) 775-2201
(800) 884-0002

Fax:

(919) 777-6399

Email:

[email protected]

Web site:

www.trioninc.com

E.

 

Before servicing or cleaning unit, switch power off at service panel and lock service
panel to prevent power from being switched on accidentally.

Содержание AIR BOSS

















Отзывы:

Нет отзывов