Trion Air Boss T1001 Module Скачать руководство пользователя

Страница: 5 / 22

see “Troubleshooting Chart”, for additional causes of
arcing.

The louvers on the grill are adjustable so the direction of
airflow can be controlled as desired.

NOTE

: The unit is equipped with an interlock switch for

your safety. The unit will not operate if the cell access
door is not closed securely.

NOTE:

an interlock switch does not protect the blower

access door on the T1300 and T2600. Do not attempt to
operate the unit unless the door is fastened securely.

DUCTING APPLICATION

The T1300 and T2600 air cleaners are designed for
both free hanging applications and limited duct system
applications. The duct systems must be carefully
designed to keep the external static pressure to a
minimum while still moving the required amount of air.
Some added static pressure could be overcome by
adjusting the blower drive pulleys or using a more
powerful motor. Capture hoods and duct design
information may be obtained from the Industrial
Ventilation Handbook or from your local Trion
representative.

To maintain the selected cleaning efficiency, it is
important to assure that the total air volume (capacity in
CFM or m3/hr) is uniformly distributed across the entire
face area of the unit. The metal mesh filters, perforated
plate or mist suppressors provide some resistance to
effect even air distribution. However, since most air
ducts are designed to handle air velocities greater than
the rated velocity of the air cleaner, it is necessary to
properly transition any attached ducting. If possible, a
contraction ratio of 1 in 3 (approximately 20

) should be

maintained. If space prohibits, turning vanes, air baffles
or other means may be utilized. Ducting – where
attached to the cabinet collars – should be gasketed,
caulked or otherwise made watertight.

III. INSTALLATION – READ THOROUGHLY

1. Carefully unpack unit from shipping crate or carton

and examine for damage in shipment.

2. Remove ionizer/collector cell(s), pre-filters and

after-filters.

3. Attach 500 pound (227 kg) test chain to the ceiling

joist using:
a. Wood joist – 3/8” (m10) eye bolts
b. Metal joist – wrap chain around joist at least

twice and secure with 500 pound (227 kg) test
connecting link

4. Chain should be cut to allow the unit to hang from a

predetermined height from the floor. (Usually 10-12
feet or 3.0-3.6 m).

5. The unit is equipped with a locator dimple in each

corner on the top and bottom. Using the dimples as
a guide, drill (4) 13/32” dia. (10.3 mm) holes that will
be required for mounting the eyebolts, which are
attached to the suspension chain.

6. Position a 3/8” (m10) diameter eyebolt (or larger) in

each hole and secure with a washer and
appropriate nuts.

NOTE

: Be sure to place two nuts on each eyebolt to

act a locking nut. Failure to do so may cause the
nuts to loosen and the unit to fall.

7. Using 3/8” (10 mm) connecting links, attach unit to

chain. Use turnbuckles on diagonally opposite
chains.

NOTE:

Foul threads on turnbuckles after leveling

unit to ensure that the turnbuckle will not "“back off"
or loosen and cause the unit to fall.

8. The units can be suspended with the direction of

airflow from the right to left. If a left to right airflow is
desired, the unit may be flipped over and the
eyehooks installed in what was originally the
bottom.

LIQUID AEROSOL APPLICATION

INSTALLATIONS

The unit is equipped with a sump, drain hole sized to
accept a ½” NPT fitting.
For the collection of liquid contaminant:

1. Install drain fitting to allow for the attachment of a

liquid collection cup or drain hose. A drain fitting is
available from your representative. An “S” trap is
required in the drain hose to ensure proper drainage
of the collected liquid.

2. Raise the front corner of the unit, opposite of the

drain corner, ½” (13 mm) to enable the collected
liquid to flow to the drain sump.